KORG Professional Engineer PA3 - Manual (Page 177)

175 Effects
Double Size
Advanced
b, c, d, e, f, g: Status
These parameters set the output status of each Tap.
Always On : Output is always on. (No modulation)
Always Off : Output is always off. (No modulation)
On → Off (dm): Output level is switched from on to off depend-
ing on the modulation source.
Off → On (dm): Output level is switched from off to on depend-
ing on the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the mod-
ulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
131: St. Pitch Shifter
(Stereo Pitch Shifter)
This is a stereo pitch shifter. The pitch shift amount for the left
and right channels can be reversed from each other.
a: L/R Pitch
When you select Up/Down for this parameter, the pitch shift
amount for the right channel will be reversed. If the pitch shift
amount is positive, the pitch of the left channel is raised, and the
pitch of the right channel is lowered.
g
Tap6 (300)
[msec]
0...2000
Sets the Tap1 (LFO phase=300
degrees) delay time
Depth 0...30 Sets the Tap6 chorus depth
Status
Always On,
Always Off,
On
Off (Dm),
Off On (Dm)
Selects on, off, or modulation source
for the control of Tap6 output
h Panning Preset
1 : L 1 2 3 4 5 6 R,
2 : L 135 246 R,
3 : L 1 3 5 2 4 6 R,
4 : L 1 4 5 6 3 2 R
Selects the stereo panning pattern
for each tap
i
Tap1 Feedback –100...+100 Sets the Tap1 feedback amount
Src Off...Tempo
Selects the modulation source for
the Tap output level, feedback
amount, and effect balance
Amt –100...+100
Sets the modulation amount of Tap1
feedback amount
j
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
a
Mode
Slow, Medium,
Fast Switches Pitch Shifter mode
L/R Pitch
Normal,
Up/Down Determines whether or not the L/R
pitch shift amount is inverted
b
Pitch Shift [1/
2tone]
–24...+24
Sets the pitch shift amount in steps
of a semitone
Src Off...Tempo
Selects the modulation source of
pitch shift amount
Amt –24...+24
Sets the modulation amount of
pitch shift amount
c
Fine [cents] –100...+100
Sets the pitch shift amount in steps
of one cent
Amt –100...+100
Sets the modulation amount of
pitch shift amount
d L Delay [msec] 0...2000
Sets the delay time for the left
channel
e R Delay [msec] 0...2000
Sets the delay time for the right
channel
f
Feedback –100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the damping amount in the
high range
g
Feedback
Position
Pre, Post Switches the feedback connection
Spread –100...+100
Sets the width of the stereo image
of the effect sound
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
Feedback Spread
FX Amt
FX Amt
Stereo In - Stereo Out
High Damp
High Damp
Input Level
Input Level
Feedback Position
Pre
Pre
Post
Post
Delay Pitch Shifter
Delay Pitch Shifter