KORG Professional Engineer PA3 - Manual (Page 145)

143 Effects
Delay
Advanced
65: Stereo/CrossDelay
This is a stereo delay, and can by used as a cross-feedback delay
effect in which the delay sounds cross over between the left and
right by changing the feedback routing.
66: St. Multitap Delay
(Stereo Multitap Delay)
The left and right Multitap Delays have two taps respectively.
Changing the routing of feedback and tap output allows you to
create various patterns of complex effect sounds.
a: Mode
You can change how the left and right delay signals are panned
by modifying the routing of the left and right delay as shown in
the figure above. You need to input different sounds to each
channel in order for this parameter to be effective.
d: Tap1 Level
This parameter sets the output level of Tap1. Setting a different
level from Tap2 will add a unique touch to a monotonous delay
and feedback.
a Stereo/Cross Stereo, Cross
Switches between stereo delay and
cross-feedback delay
b
L Delay Time
[msec]
0.0...1360.0
Sets the delay time for the left
channel
c
R Delay Time
[msec]
0.0...1360.0
Sets the delay time for the right
channel
d
L Feedback –100...+100
Sets the feedback amount for the
left channel
Src Off...Tempo
Selects the modulation source of
feedback amount
Amt L –100...+100
Sets the modulation amount of the
left channel feedback
e
R Feedback –100...+100
Sets the feedback amount for the
right channel
Amt R –100...+100
Sets the modulation amount of the
right channel feedback
f High Damp [%] 0...100
Sets the damping amount in the
high range
g Low Damp [%] 0...100
Sets the damping amount in the low
range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i Spread –50...+50
Sets the width of the stereo image
of the effect sound
j
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Delay
Delay
Stereo/Cross
Left
Right
Feedback
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp Low Damp
Spread
Stereo/Cross
a Mode
Normal, Cross
Feedback,
Cross Pan1,
Cross Pan2
Switches the left and right delay
routing
b
Tap1 Time
[msec]
0.0...1360.0 Sets the Tap1 delay time
c
Tap2 Time
[msec]
0.0...1360.0 Sets the Tap2 delay time
d Tap1 Level 0...100
Sets the Tap1 output level
e
Feedback
(Tap2)
–100...+100 Sets the Tap2 feedback amount
Src Off...Tempo
Selects the modulation source of
the Tap2 feedback amount
Amt –100...+100
Sets the modulation amount of the
Tap2 feedback amount
f High Damp [%] 0...100
Sets the damping amount in the
high range
g Low Damp [%] 0...100
Sets the damping amount in the low
range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i
Spread –100...+100
Sets the width of the stereo image
of the effect sound
Src Off...Tempo
Selects the modulation source of
the effect sound’s stereo image
width
Amt –100...+100
Sets the modulation amount of the
effect sound’s stereo image width
j
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
Feedback
Spread
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp Low Damp
Delay
Delay
Feedback
Tap1 Level Mode Mode
(1)
(2)
(1)
(2)
Tap1=(1)
Tap2=(2)
Mode: Normal Mode: Cross Feedback Mode: Cross Pan1 Mode: Cross Pan2