KORG Professional Engineer PA3 - Manual (Page 132)

130 Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
44: St. Random Phaser
(Stereo Random Phaser)
This is a stereo phaser. The effect uses a step-shape waveform
and random LFO for modulation, creating a unique phasing
effect.
45: St. Env. Phaser
(Stereo Envelope Phaser)
This stereo phaser uses an envelope generator for modulation.
You will obtain the same pattern of phasing each time you play.
You can also control the Phaser directly using the modulation
source.
a
LFO Waveform
Step-Tri, Step-
Sin, Random
Selects the LFO Waveform
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
b
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects the modulation source
commonly used for LFO speed and
step speed
Amt
–20.00...
+20.00 Sets the modulation amount of LFO
speed
c
LFO Step Freq
[Hz]
0.05...50.00 Sets the LFO step speed
Amt
–50.00...
+50.00 Sets the modulation amount of LFO
step speed
d
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00 MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
e
Step Base Note r...w
Selects the type of notes to specify
the LFO step speed
Times x1...x32
Sets the number of notes to specify
the LFO step speed
f
Manual 0...100
Sets the frequency to which the
effect is applied
Src Off...Tempo
Selects the modulation source for
the LFO modulation
Amt –100...+100
Sets the modulation amount of the
LFO modulation
g Depth 0...100 Sets the depth of LFO modulation
h
Resonance –100...+100
Sets the resonance amount
High Damp [%] 0...100
Sets the resonance damping
amount in the high range
i
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
LFO: Step-Tri/Random
Left
Right
Resonance
LFO Phase
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
Phaser
Phaser
a
L Manu
Bottom
0...100
Sets the lower limit of the frequency
range for the effect on the left
channel
L Manu Top 0...100
Sets the upper limit of the frequency
range for the effect on the left
channel
b
R Manu
Bottom
0...100
Sets the lower limit of the frequency
range for the effect on the right
channel
R Manu Top 0...100
Sets the upper limit of the frequency
range for the effect on the right
channel
c
Sweep Mode EG, D-mod
Determines whether the flanger is
controlled by the envelope
generator or by the modulation
source
Src Off...Tempo
Selects the modulation source that
triggers the EG (when EG is selected
for Sweep Mode), or modulation
source that causes the flanger to
sweep (when D-mod is selected for
Sweep Mode)
d
EG Attack 1...100
Sets the EG attack speed
EG Decay 1...100
Sets the EG decay speed
e Resonance –100...+100
Sets the resonance amount
f High Damp [%] 0...100
Sets the resonance damping
amount in the high range
g
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
EG Attack/Decay
EG
D-mod
Sweep Mode
D -mod
Phaser
Phaser
Left
Right
Resonance
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out