Panasonic WJ-FS616C - Manual (Page 37)

37
■ Camera Title Setup
This item lets you edit the camera title to be displayed on
the monitor screen.
Up to 8 alphanumeric characters can be displayed on the
monitor.
1. Move the cursor to TITLE SETUP in the SYSTEM SETUP
menu by pressing the C or D button, then press the
[HOME/SET] button.
The TITLE SETUP menu shown in the figure appears on
the monitor screen.
2. Move the cursor to the channel you want to edit by
pressing the C or D button, then press the
[HOME/SET] button.
The cursor moves to the right editing column, and the
square cursor appears on the character table.
3. To select a character, move the cursor on the desired
character in the table by pressing the C, D, A or B
button.
4. Then press the [HOME/SET] button to pick up the char-
acter, and place it in the editing column.
5. Repeat steps 3 and 4 above until the title for a certain
camera is completed.
6. If a wrong character is selected, press the - or + but-
ton to move the cursor in the editing column.
Note: Press the + button to move the cursor to the
right, or press the - button to move the cursor to
the left.
Then press the [HOME/SET] button to overwrite
the character with the character selected in the table.
7. Press the [SET UP/ESC] button to move the cursor to
the channel number column.
8. Press the [FUNCTION] button to display the next page,
then press this button again to return to the previous
page.
9. Repeat steps 2 to 7 above to edit the titles for the rest of
the cameras.
10. After completing the setting, press the [SET UP/ESC]
button to return to the previous SYSTEM SETUP menu.
■ Camera Title Display Position
This item lets you select the camera title position to be dis-
played on the monitor screen.
Refer to the Clock Display Position Setting on page 36 for
more details.
1. Move the cursor to TITLE POSITION in the SYSTEM
SETUP menu, then press the [HOME/SET] button.
The position setting menu appears on the monitor
screen.
2. Move the title by pressing the C, D, A or B button.
Note: In the Multiscreen display with the multiscreen
output or record output, the clock display is shifted
one line from the preset position if the camera title
and the clock are preset to the same position.
3. Press the [SET UP/ESC] button to execute the selection
and return to the previous SYSTEM SETUP menu.
■ Sequence Setup
This item lets you program the sequence pattern for spot or
multi sequence.
You can either program a spot sequence (SEQ1) or two
multi sequences (SEQ2, SEQ3).
● Spot Sequence (SEQ1)
This item lets you program or edit a spot sequence.
Up to 32 steps can be assigned in the table shown in the
figure.
You can also enable the auto skip function to skip any
steps where no video signal is present.
The duration of each step is determined by the dwell time
setting.
The factory default setting is sequential display of 16 cam-
era images.
1. Move the cursor to the SEQUENCE SETUP parameter in
the SYSTEM SETUP menu.
TITLE SETUP 1 OF 2
1CH 1------- 0123456789
2CH 2------- ABCDEFGHIJK
3CH 3------- LMNOPQRSTUV
4CH 4------- WXYZ
5CH 5------- abcdefghijk
6CH 6------- imnopqrstuv
7CH 7------- wxyz
8CH 8-------
' ¤ =?'"#&()*
+,-./:; E
@
TITLE SETUP 2 OF 2
9CH 9------- 0123456789
10CH 10------ ABCDEFGHIJK
11CH 11------ LMNOPQRSTUV
12CH 12------ WXYZ
13CH 13------ abcdefghijk
14CH 14------ imnopqrstuv
15CH 15------ wxyz
16CH 16------
' ¤ =?'"#&()*
+,-./:; E
@