Roland VG-99 - Manual (Page 127)

127
FX (Effects) Chapter 9 Parameters Guide
Chapter 9
MOD1, MOD2
With MOD1 and MOD2, you can select the effect to be used from the
following.
You can select the same effect for FX-1 and FX-2.
PHASER
By adding varied-phase portions to the direct sound, the phaser
effect gives a whooshing, swirling character to the sound.
MOD TYPE
MOD1
MOD2
Common
PHASER Phaser (p. 127)
FLANGR Flanger (p. 128)
TREML Tremolo (p. 128)
PAN Pan (p. 128)
T.WAH Touch Wah (p. 129)
AUTO WAH Auto Wah (p. 129)
OCTAVE Octave (p. 129)
PITCH SHIFT Pitch Shifter (p. 130)
HARMONIST Harmonist (p. 130)
PEDAL BEND Pedal Bend (p. 132)
2x2 CHORUS 2x2 Chorus (p. 132)
ROTARY Rotary (p. 133)
UNI-V Uni-V (p. 133)
VIB Vibrato (p. 133)
SLICER Slicer (p. 134)
HUMANIZER Humanizer (p. 134)
SLOW GEAR Slow Gear (p. 135)
DEFRET Defretter (p. 135)
FEEDBACKER Feedbacker (p. 135)
RING MOD Ring Modulator (p. 136)
ANTI FB Anti Feedback (p. 136)
ADV.COMP Advanced Compressor (p. 136)
LIMITR Limiter (p. 137)
SUB EQ Sub Equalizer (p. 137)
SUB DELAY Sub Delay (p. 138)
Parameter/
Range
Explanation
MOD1 SW, MOD2 SW (MODE Switch)
OFF, ON Turns the MOD-1 (MOD-2) effect on/off.
MOD 1 TYPE, MOD 2 TYPE (MODE Type)
see above Selects the effect to be used.
Parameter/
Range
Explanation
TYPE
Selects the number of stages that the phaser effect will use.
4STG This is a four-phase effect. A light phaser ef-
fect is obtained.
8STG This is an eight-phase effect. It is a popular
phaser effect.
12STG This is a twelve-phase effect. A deep phase
effect is obtained.
BI-PHS This is the phaser with two phase shift cir-
cuits connected in series.
RATE
0–100,
BPM –BPM
This sets the rate of the phaser effect.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 163) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
DEPTH
0–100 Determines the depth of the rotation effect.
MANUAL
0–100 Adjusts the center frequency of the rotation
effect.
RESO (Resonance)
0–100 Determines the amount of resonance (feed-
back).
Increasing the value will emphasize the ef-
fect, creating a more unusual sound.
STEP RATE
Off, 0–100,
BPM –BPM
This sets the cycle of the step function that
changes the rotation. When it is set to a
higher value, the change will be finer. Set
this to Off when not using the Step function.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 163) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
EFFECT LEVEL
0–100 Adjusts the volume of the phaser.
DIRECT LEVEL
0–100 Adjusts the volume of the direct sound.
VG-99_e.book 127 ページ ２００７年７月５日 木曜日 午前９時２２分