Roland VG-99 - Manual (Page 165)

165
GUITAR TO MIDI Chapter 9 Parameter Guide
Chapter 9
SYSTEM
These parameters are applied to the entire VG-99 in the GUITAR TO
MIDI function.
Parameter/
Range
Explanation
CC (Control Change)
You can output the actions of the controllers specified with SRC as
Control Change messages.
You can make two types of settings, 1 and 2.
SRC (Source)
GK VOL GK-3 GK volume knob
GK S1 GK-3 DOWN/S1 switch
GK S2 GK-3 UP/S2 switch
CTL1 Control button1
CTL2 Control button2
EXP PEDAL Expression pedal connected to the EXP
PEDAL jack
CTL3 Footswitch connected to the CTL3,4 jack
(jack tip)
CTL4 Footswitch connected to the CTL3,4 jack
(jack ring)
D BEAM V D BEAM vertical movements
D BEAM H D BEAM horizontal movements
RIBBON ACT RIBBON CONTROLLER touch
RIBBON POS RIBBON CONTROLLER position
FC-300 EXP1 FC-300 expression pedal1
FC-300 EXPSW1 FC-300 expression pedal switch1
FC-300 EXP2 FC-300 expression pedal2
FC-300 EXPSW2 FC-300 expression pedal switch2
FC-300 CTL1 FC-300 control pedal1
FC-300 CTL2 FC-300 control pedal2
FC-300 E3/C3 FC-300 external expression pedal3/external
footswitch3
FC-300 CTL4 FC-300 external footswitch4
FC-300 E4/C5 FC-300 external expression pedal4/external
footswitch5
FC-300 CTL6 FC-300 external footswitch6
FC-300 E5/C7 FC-300 external expression pedal5/external
footswitch7
FC-300 CTL8 FC-300 external footswitch8
CC (Control Change)
OFF, #1–#31, #64–#95 This sets the Control Change number to be
output.
* When the MONO/POLY setting is set to
POLY, messages are output only over the
basic channel; when this is set to MONO, the
messages are output over the six channels
starting from the basic channel.
TX PC STRING 1–6
This sets the Program Change messages for each string that are out-
put when the VG-99’s patches are switched.
BANK MSB
OFF, 1–127 This sets the Bank Select (MSB).
BANK LSB
OFF, 1–127 This sets the Bank Select (LSB).
Parameter/
Range
Explanation
PC (Program Change)
OFF, 1–128 This sets the Program Number.
Parameter/
Range
Explanation
HOLD CTL (Hold Control)
This setting determines the controller used for the HOLD function.
GK S1, S2 GK-3 DOWN/S1, UP/S2 switch
CTL1, 2 Control button1, 2
CTL3 Footswitch connected to the CTL3,4 jack
FC-300 CTL1,2 FC-300 control pedal1, 2
FC-300 CTL3–8 FC-300 external footswitch3–8
BEND THIN
OFF, ON Setting this to ON thins out the Pitch Bend
messages and reduces the volume of MIDI
data.
BASIC CH (Basic Channel)
1–11 This sets the MIDI transmit channel used for
the GUITAR TO MIDI function.
PC MASK (Program Change Mask)
OFF, ON When set to ON, the Bank Select messages
and Program Change messages used for the
GUITAR TO MIDI function are not trans-
mitted when patches are changed.
VG-99_e.book 165 ページ ２００７年７月５日 木曜日 午前９時２２分