Roland VG-99 - Manual (Page 69)

69
Chapter 6 Using MIDI
Chapter 6
Selecting How the Hold Functions
(HOLD TYPE)
This selects the Hold function type when the controller set with the
HOLD CTL parameter (p. 65) is adjusted.
1. Follow Steps 1–2 in “Setting the Transmission
Mode (MODE)” (p. 67) to display the GTR TO
MIDI screen.
2. Press PAGE [ ] to display Page 1.
3. Use [F1] (SELECT) or the F1 knob to select
MONO.
4. Adjust the setting with [F4] (SELECT) or the F4
knob.
• HOLD 1
The Note On messages are held when the Hold function is
switched on with the controller.
If the Hold function remains on as you continue to play the
strings, each successive Note On message is held, and when a
Note message is already being played from the same string,
the previous Note message is cancelled, and the next Note On
message is held. This allows you to prevent any interruption
in the sounds, even sounds from releasing the strings over the
frets.
• HOLD 2
The Note On messages are held when the Hold function is
switched on with the controller.
However, subsequent Note On messages are not output if you
continue to play the instrument with the Hold effect left on.
• HOLD 3
The Note On messages are held when the Hold function is
switched on with the controller.
If the Hold function remains on as you continue to play the
strings, Note On messages for strings other than the one
already being held can be output, but they are not held.
Outputting Control Changes by
Operating the Controllers (CC)
You can operate the panel knobs and pedals to output Control
Change messages.
There are two different settings.
1. Follow Steps 1–2 in “Setting the Transmission
Mode (MODE)” (p. 67) to display the GTR TO
MIDI screen.
2. Press PAGE [ ] [ ] to display Page 2.
3. Use [F1] (SELECT) or the F1 knob, or [F4]
(SELECT) or the F4 knob, to select the
controller you want to set.
4. Use [F2] (SELECT) or the F2 knob, or [F5]
(SELECT) or the F5 knob, to select the Control
Change number you want to output.
Off, CC #1–#31, CC #64–#95
SRC Controller
GK VOL GK-3 Volume knob
GK S1 GK-3 DOWN/S1 Switch
GK S2 GK-3 UP/S2 Switch
CTL1 Control Button 1
CTL2 Control Button 2
EXP PEDAL External Expression Pedal
CTL3 External Footswitch 3
CTL4 External Footswitch 4
D BEAM V D BEAM Height
D BEAM H D BEAM Left-Right
RIBBON ACT Ribbon Controller Touch
RIBBON POS Ribbon Controller Touch Position
FC-300 EXP1 FC-300’s EXP PEDAL 1
FC-300 EXPSW1 FC-300’s EXP PEDAL SW1
FC-300 EXP2 FC-300’s EXP PEDAL 2
FC-300 EXPSW2 FC-300’s EXP PEDAL SW2
FC-300 CTL1 FC-300’s CTL1
FC-300 CTL2 FC-300’s CTL2
FC-300 E3/C3
FC-300’s External Expression Pedal 3,
External Footswitch 3
FC-300 CTL4 FC-300’s External Footswitch 4
FC-300 E4/C5
FC-300’s External Expression Pedal 4,
External Footswitch 5
FC-300 CTL6 FC-300’s External Footswitch 6
FC-300 E5/C7
FC-300’s External Expression Pedal 5,
External Footswitch 7
FC-300 CTL8 FC-300’s External Footswitch 8
VG-99_e.book 69 ページ ２００７年７月５日 木曜日 午前９時２２分