Roland MC-909 - Manual (Page 139)

139
About V-LINK
V-LINK
V-LINK settings
Resetting the image
* For details on clips/palettes, dissolve time, color difference signals (Cb/
Cr), refer to the Edirol DV-7PR manual.
The MC-909 does not support the Edirol DV-7PR’s dual stream
mode.
Parameter Range Explanation
Note Tx Ch 1–16 MIDI channel that will switch Edirol DV-7PR clips/palettes and will control dissolve time.
Clip 1 Note No. 0(C-1)–127(G9) Note number (velocity pad) that corresponds to Edirol DV-7PR clip 1
If this is set to 59 (B3), velocity pads 1–16 will correspond to clips 1–16.
Play Speed Ctrl 0.0–1.0–2.0, 0.5–1.0–2.0,
0.0–1.0–4.0, 0.5–1.0–4.0,
0.0–1.0–8.0, 0.5–1.0–8.0,
0.0–1.0–16.0, 0.5–1.0–16.0,
0.0–1.0–32.0, 0.5–1.0–32.0,
0.0–2.0–4.0, 0.0–4.0–8.0,
0.0–8.0–16.0, 0.0–16.0–32.0,
-2.0–1.0–4.0, -6.0–1.0–8.0 Range of video playback speed
The three values are the playback speeds (multiples of normal speed) at the negative,
center, and positive positions of the turntable emulation slider.
Dissolve Time OFF, CC1, CC5, CC7, CC10,
CC11, CC71–74, CC91–93,
Channel Aftertouch Control change number that controls the dissolve time (time over which the image switch-
es)
Ctrl Tx Ch 1–16 MIDI channel that will control the Edirol DV-7PR color Cb/Cr, brightness, and video effect
switching
Color Cb Ctrl OFF, CC1, CC5, CC7, CC10,
CC11, CC71–74, CC91–93,
Channel Aftertouch Control change number that controls the Cb color of the image
Color Cr Ctrl Control change number that controls the Cr color of the image
Brightness Ctrl Control change number that controls the brightness of the image
VFX1–4 Ctrl Control change number that controls the video effect
* VFX2–4 are not supported by the Edirol DV-7PR.
Fade Ctrl Control change number that controls the output fade
PAD MODE CLIP, PALETTE Selects whether the velocity pads will switch clips or palettes.
Press [F1 (Clip mode)]: switch clips
Press [F2 (Palette)]: switch palettes
Local Sw OFF, ON Specifies whether the internal sound generator is disconnected (OFF) from the velocity
pads, or not (OFF).
Clip filter
(check boxes 1–32) (OFF), ✔ (ON) Enable/disable switching for each clip
Clips that are checked can be switched (see explanatory box below)
Using the Clip Filter
For example, suppose that of the rhythm set you input in the
part used for V-LINK (i.e., the part of the same number as the
Note Tx Channel), you want only the kick and snare to switch
clips. In this case, check only the clips that correspond to the
note numbers of the kick and snare. The clips will switch when
the kick or snare plays.
[F3 (Clip Reset)] Turn off the image (solid black).
[F4 (All Reset)] The effect applied to the image will be reset,
and brightness, color difference, etc. will all
return to the default value.
MC-909_Ref_e.book 139 ページ ２００５年３月１日 火曜日 午後３時２９分