Roland MC-909 - Manual (Page 95)

95
Multi-Effects List
Effects
11:STEREO PHASER
This is a stereo phaser.
fig.MFX11
12:STEP PHASER
With the Step effects, you can also make stepped changes in the pitch
of sounds to which the Phaser effect is applied.
fig.MFX12
13: RING MODULATOR
This is an effect that applies amplitude modulation (AM) to the input signal,
producing bell-like sounds. You can also change the modulation frequency
in response to changes in the volume of the sound sent into the effect.
fig.MFX13
14: TREMOLO
Cyclically modulates the volume to add tremolo to the sound.
fig.MFX14
Parameter Value Description
Mode 4, 8 stage Number of stages in the phaser
Polarity INVERSE,
SYNCHRO Selects whether the left and right
phase of the modulation are the
same or opposite each other.
INVERSE: The left and right
phase are opposite. When using a
mono source, this spreads the
sound in stereo.
SYNCHRO: The left and right
phase are the same. Select this
when working with a stereo source.
Rate #2 0.05–10.00
Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Manual #1 0–127 Adjusts the basic frequency from
which the sound is modulated.
Resonance 0–127 Amount of feedback
Cross
Feedback -98– +98 % Adjusts the amount of the phaser
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
Mix 0–127 Level of the phase-shifted sound
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
Parameter Value Description
Mode 4, 8 stage Number of stages in the phaser
Polarity INVERSE,
SYNCHRO Selects whether the left and right
phase of the modulation are the
same or opposite each other.
INVERSE: The left and right
phase are opposite. When using a
mono source, this spreads the
sound in stereo.
SYNCHRO: The left and right
phase are the same. Select this
when working with a stereo source.
R in R out
L in L out Phaser
Mix
2-Band
EQ
Phaser 2-Band
EQ
Mix
R in R out
L in L out Step Phaser
Mix
2-Band
EQ
Step Phaser
2-Band
EQ
Mix
Rate 0.05–10.00
Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Manual #1 0–127 Adjusts the basic frequency from
which the sound is modulated.
Resonance 0–127 Amount of feedback
Cross
Feedback -98– +98 % Adjusts the amount of the phaser
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
Step Rate
#2 0.1–20.0
Hz, note Rate of pitch change
Mix 0–127 Level of the phase-shifted sound
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
Parameter Value Description
Frequency
#1 0–127 Adjusts the frequency at which
modulation is applied.
Sens 0–127 Adjusts the amount of frequency
modulation applied.
Polarity UP,
DOWN Determines whether the frequency
modulation moves towards higher
frequencies (
UP ) or lower frequen-
cies ( DOWN ).
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance #2 D100:0W–
D0:100W Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
Parameter Value Description
Modula-
tion Wave TRI, SQR,
SIN,
SAW1,
SAW2 Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1: sawtooth wave (upward)
SAW2: sawtooth wave (down-
ward)
Rate #1 0.05–10.00
Hz, note Frequency of the change
Depth #2 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
Parameter Value Description
L in
R in
L out
R out
Ring Mod
2-Band EQ
2-Band EQ
Ring Mod
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
MC-909_Ref_e.book 95 ページ ２００５年３月１日 火曜日 午後３時２９分