Trango Broadband Access5830 - Manual (Page 29)

Basic Configuration via CLI
Trango Broadband Wireless — Access5830 User Manual Rev. F page 25
Subscriber Unit Basic Settings
Log into the SU. To receive a comprehensive snapshot of the system’s configuration info and status, type the command
sysinfo.
#> sysinfo
[Hardware Version] 0004
[FPGA Version] 03110601 [Checksum] 1D28DCC4
[Firmware Version] FSU 1p01H0004D03100101 [Checksum] 191D17BC
[Device ID] 00 01 DE 12 4F DF [Base ID] 11 [AP ID] 1 [SU ID] 44
[System Up Time] 0 day(s) 00:04:20
[Radio Temperature] 35
[Opmode] su [Default Opmode] su [Opmode Start] 30 sec
[IP] 10.8.0.252 [Subnet Mask] 255.255.255.0 [Gateway] 10.8.0.1
[Httpd Port] 80 [Httpd Status] listen
[Telnetd Port] 23 [Telnetd Status] connected (10.8.0.2,1041)
[Tftpd] disabled
[RF Tx Power] 22 dBm
[RF Rx Threshold] -90 dBm
Channel Table: (MHz)
[Ch#01] 5736 [Ch#02] 5756 [Ch#03] 5776 [Ch#04] 5796 [Ch#05] 5816 [Ch#06] 5836
[Ch#07] 5260 [Ch#08] 5280 [Ch#09] 5300 [Ch#10] 5320 [Ch#11] 5340 [Ch#12] 5736
[Ch#13] 5736 [Ch#14] 5736 [Ch#15] 5736 [Ch#16] 5736 [Ch#17] 5736 [Ch#18] 5736
[Ch#19] 5736 [Ch#20] 5736 [Ch#21] 5736 [Ch#22] 5736 [Ch#23] 5736 [Ch#24] 5736
[Ch#25] 5736 [Ch#26] 5736 [Ch#27] 5736 [Ch#28] 5736 [Ch#29] 5736 [Ch#30] 5736
[Channel Scan Sequence] 6 v
[Active Channel] 6 v Disconnected
[Broadcast Packet] block [Auto Scan AP] on [TCP/IP for AP] on [TCP/IP LocalEth]on
[Remarks] Attica
[RF Rx] 0 kbps [RF Tx] 0 kbps [Eth Rx] 3 kbps [Eth Tx] 8 kbps
Success.
Many of these parameters can be changed by the user. A description of each of these changeable parameters, along with
the related command, is shown in the table below.
!
Important! When changing settings, it is usually necessary to type the save ss command in order to update the
radio’s flash memory. If you do not type the save ss command, the setting will be lost the next time the radio is
rebooted or power cycled. The command save ss is equivalent to the command updateflash systemsetting.
Table 3: Reference Table of Basic SU System Information
SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
SU Parameter Description Related CLI Command
Device ID MAC Address of the SU N/A
Base ID Specifies the cell or cluster to
which the SU belongs. set baseid <baseid>
Example:
#>Set baseid 10
SU ID Together with Base ID, it is
the unique identifier of this SU
used in association. It is used
to execute commands from the
AP to this specific SU. set suid <suid>
Example:
#>Set suid 3
AP ID Informational parameter that
shows to which AP the SU is
associated. Please note that
AP ID is not used by the
system for SU authentication. Informational Parameter
Opmode Current Opmode of radio. opmode su [< y>]
This sets the radio in Opmode “SU.” To set the radio
in Opmode “OFF,” reboot and access radio via
Ethernet port within the first 30 seconds.
Default Opmode Determines the Opmode (“SU”
or “OFF”) of the radio after
reboot/power cycle. When the
parameter is set to “SU,” the set defaultopmode <su | off>