Yamaha AW2400 - Manual (Page 107)

Displaying the mix parameters for individual channels
107
AW2400 Owner’s Manual
Channel Oper
ation
12
E COMP
Move the cursor to the symbol below COMP and press
the [ENTER] key to turn the compressor for that channel
on or off or select the compressor insert point.
Press the [ENTER] key repeatedly to sequentially select
the following insert points.
Refer to “Using the Compressors” on page 152 for details.
F ON/OFF, LVL knob
• ON/OFF ..........Move the cursor to this position and
press the [ENTER] key to turn the chan-
nel on or off. This function is linked to
the channel [ON] keys.
• LVL knob ........Move the cursor to this knob and use
the [DATA/JOG] dial or [INC]/[DEC] keys
to adjust the channel level. This function
is linked to the channel faders.
G INSERT EFF
This parameter is used to insert an internal effect to a
specified point in the channel, or to specify an insert point
for insertion of an external effect.
If you move the cursor to the field to the right of INSERT
EFF and press the [ENTER] key, a popup window will
appear allowing selection of an internal effect or I/O chan-
nel on an optional I/O card.
H PAN/BAL knob
Move the cursor to this knob and use the [DATA/JOG]
dial or [INC]/[DEC] keys to pan the channel signal to the
stereo bus or bus 1 and bus 2 (for stereo input channels
this functions as a balance control). The effect return
channel L and R signals can be adjusted individually.
These knobs are linked to the PAN/EQ screen knobs (
→
p. 147).
I BUS1, BUS2, ST
Move the cursor to any of these points and press the
[ENTER] key to turn assignment of the channel signal to
the corresponding bus – bus 1, bus 2, or stereo bus – on or
off.
J REC TR
Displays the input channel to track assignment, as speci-
fied in the RECORD screen Direct page.
K Level meter
The level meters display input channel, track channel and
effect return channel input levels, as well as stereo output
channel, bus master channel, AUX send master channel,
effect send master channel output levels.
L AUX, EFFECT
Move the cursor to the appropriate knob and use the
[DATA/JOG] dial or [INC]/[DEC] keys to adjust send lev-
els to AUX bus 1–4 or effect bus 1–4 over a range of from
–
∞ to +10dB. You can also move the cursor to one of
these knobs and press the [ENTER] key to turn the corre-
sponding send off. Further, if you move the cursor to the
signal path above the knob and press the [ENTER] key
you can switch between pre-fader (PRE) and post-fader
(POST) send.
These functions are linked to the AUX and EFFECT
screens (
→ p. 111, 115).
C After the channel fader
D Compressor off
B Before the channel fader
A Before the channel EQ
To A
• You can move the cursor to the insert point and press the [ENTER]
key to reverse the order of the COMP and an INSERT EFF.
HINT
• Since no EQ is provided on the effect send master channels, the
compressor can be inserted either pre-fader or post-fader.
NOTE
• For details on insert effect operation refer to “Inserting an Effect
Into a Channel” on page 119.
• When SLOT1–16 is selected the specified channel insert point is
assigned to the corresponding channel on an optional I/O card
installed in the AW2400. This assignment is shown in the PATCH
screen Output page OPTION I/O SLOT OUT ASSIGN field.
• You can move the cursor to the insert point and press the [ENTER]
key to reverse the order of the COMP and an INSERT EFF.
HINT
• Signals cannot be sent to the effect buses from an effect return
channel.
NOTE