Electro Cam 5000 Series - Manual (Page 31)

4-3 Programming, Standard Features
Note: When entering multiple pulses, press ENT after each
CREATE SETPOINTS
CLEAR SETPOINTS
Output Setpoint Programming
Programming Error Messages
Flashing error messages indicate programming mistakes
as they occur.
Simply press to cancel flashing error message.
POS CHN PGM FCN
CLR
If POS or RPM
led NOT lit press:
POS or RPM
led now lit
SELECT OUTPUT CHANNEL
POS
RPM
CHN
1 6
VIEW SETPOINTS
View setpoints of output channel presently selected.
E1 OLAP: Output pulse just attempted overlapped an existing output
pulse on same channel.
E2 -run: Attempted programming can NOT be done while machine is
running (transducer is turning).
E4 -Pro: Program enable Off when programming was attempted.
E5 8888: Value entered NOT valid for item being programmed.
E6 -379: Invalid setpoint entered: A setpoint ending in 3, 7, or 9 was
entered. (Encoder Only - Exceptions: 89, 179, 269, and 359)
E7 -dEF: Attempted to program too many Enable Inputs (FCN 9).
E9-tdE: Attempted to program too many timed outputs (FCN 5).
E11-ScE: Attempted to program more than 16 speed compensated
outputs (48 I/O controls only).
See pgs. A-12 thru A-14 for more details on error messages.
Output Setpoint Programming
Desired output channel MUST be selected before its
setpoints can be created, viewed, adjusted, or cleared.
CHN and POS
displays blank 1st Digit shown
in CHN display 2 Digit value in
CHN display
ON/OFF setpoints shown in position
display in increasing order with ON
and OFF LEDs. 0 is shown and both
LEDs off if no setpoints exist. ON/OFF setpoints shown in position
display in decreasing order with ON
and OFF LEDs. 0 is shown and both
LEDs off if no setpoints exist.
VIEW VIEW VIEW VIEW
Channel 16 used as example.
CLEAR 1 PULSE
To clear 1 pulse (1 pair of setpoints) on selected output channel.
Use numeric entry method (shown in CHANGE SET-
POINTS above) to set OFF setpoint equal to ON setpoint
value. Both setpoints will be erased.
To clear all setpoints on selected output channel.
CLEAR EXISTING SETPOINTS
ON Led lit,
POS blanks
ON OFF
0 shown in
POS display 0 shown in
POS
display OFF Led
lit, POS
blanks
ENT
POS display
blinks and
shows 0, ON
and OFF LEDs
are off.
0 0
To change all setpoints in the output channel simultaneously.
MULTI-PULSE MODE
PULSE MODE
To change both setpoints of a pulse simultaneously.
CHANGE SETPOINTS
Pulse led lit
OR
INC/DEC
NUMERIC ENTRY
To change setpoints in output channel presently selected.
PULSE
INC DEC PULSE
INC DEC INC DEC
Displayed ON/OFF setpoint increases 1
increment each time INC key is pressed. Displayed ON/OFF setpoint decreases 1
increment each time DEC key is pressed.
5
1st Digit shown in
POS display
0
2 Digits shown in
POS display
ENT
POS display blinks once to
confirm setpoint change.
Changing setpoint to 50 degrees used as example.
ON and OFF setpoints of ALL pulses
increase/decrease 1 increment each
time INC/DEC key is pressed.
ON and OFF setpoints of ALL pulses
increase/decrease 1 increment each
time INC/DEC key is pressed.
DEC INC
OR
Pulse led lit
PULSE
Pulse led
blinking
1st Digit shown in
POS display OFF led lit, POS
blank POS display blinks
once to confirm
setpoint entry. 2 Digits shown in
POS display
1st Digit shown in
POS display 2 Digits shown in
POS display On led lit, POS
blank
ON 3 0
OFF 6 0 ENT
On at 30 degrees used as example.
Off at 60 degrees used as example.
To create setpoints in output channel presently selected.
pulse.