Konica Minolta bizhub PRESS C8000e - Manual (Page 633)

bizhub PRESS C8000/e 12-59
12.9 Operator Call 12
105-04 Large Capacity
Stacker LS-505 (1st
unit if two units are
combined) The stacker of Large Ca-
pacity Stacker LS-505 (1st
unit if two units are com-
bined) has moved down to
an abnormal position. Remove the output sheets from
the stacker. For details, see Sec-
tion 5 of the User's Guide - Copier.
106-00 Large Capacity
Stacker LS-505 (2nd
unit) Output sheets are left on the
stacker of Large Capacity
Stacker LS-505 (2nd unit). Remove the output sheets from
the stacker of the 2nd unit.
106-01 Large Capacity
Stacker LS-505 (2nd
unit) The 2nd unit of Large Ca-
pacity Stacker LS-505
stopped abnormally. Make sure Large Capacity
Stacker LS-505 (1st unit) is firmly
plugged in the power outlet of Re-
lay Unit RU-508.
106-02 Large Capacity
Stacker LS-505 (2nd
unit) The stacker of Large Ca-
pacity Stacker LS-505 (2nd
unit) is rising. Wait until the stacker automatical-
ly stops rising.
106-03 Large Capacity
Stacker LS-505 (2nd
unit) The stacker of Large Ca-
pacity Stacker LS-505 (2nd
unit) is moving down. Wait until the stacker automatical-
ly stops moving down.
106-04 Large Capacity
Stacker LS-505 (2nd
unit) The stacker of Large Ca-
pacity Stacker LS-505 (2nd
unit) has moved down to an
abnormal position. Remove the output sheets from
the stacker. For details, see Sec-
tion 5 of the User's Guide - Copier.
107-00 Relay Unit RU-508 Relay Unit RU-508 is not
supplied with power. Turn off the sub power switch of
the main body, and then plug the
power cord of Relay Unit RU-508
into the power outlet of the main
body. After that, turn the sub
power switch of the main body
on again.
108-00 Perfect Binder
PB-503 Perfect Binder PB-503 is
not supplied with power. Turn off the sub power switch of
the main body, and then plug the
power cord of Perfect Binder PB-
503 into the power outlet of Relay
Unit RU-508. After that, turn the
sub power switch of the main
body on again.
108-01 Perfect Binder
PB-503 Output sheets are left inside
Perfect Binder PB-503. Move the output sheets from the
perfect binder tray to the car-
riage, and then take out those
sheets from the carriage. For de-
tails, see Section 5 of the User's
Guide - Copier.
108-02 Perfect Binder
PB-503 Available body thickness for
perfect binding is exceeded. Perfect binding is unavailable.
Cancel the job, and then remove
output sheets from inside Perfect
Binder PB-503.
108-03 Perfect Binder
PB-503 The cut-off width of perfect
binding covers is too short. Reload the perfect binding cover
tray with covers having longer cut-
off width.
Perfect binding covers are
too long. Reload the perfect binding cover
tray with shorter covers.
Perfect binding covers are
too short. Reload the perfect binding cover
tray with longer covers.
108-04 Perfect Binder
PB-503 Glue has got stuck. Contact your service representa-
tive.
110-00 Multi Punch GP-501 Multi Punch GP-501 is not
supplied with power. Make sure Multi Punch GP-501 is
firmly plugged in the outlet of ex-
ternal power supply. Also, check if
the power switch located inside
Multi Punch GP-501 is turned on.
Code Location Cause Remedy