Boss Audio Systems Boss CDSM AMP EFFECTS PROCESSOR GT-100 - Manual (Page 31)

31
CTL/EXP
ACCEL/CTL, EXP SW, SUB CTL 1, SUB
CTL 2
Here’s how to assign the parameters that will be controlled by the ACCEL/
CTL, EXP SW, SUB CTL 1 and SUB CTL 2 pedals .
Parameter Value Explanation
FUNC
OFF No assignment .
ACCEL Switches the ACCEL effect on and off .
P .LOOP ON/OFF Switches the PHRASE LOOP on and off .
P .LOOP REC/PLY Records/plays back the phrase .
P .LOOP STP/PLY Stops/plays back the phrase .
P .LOOP CLEAR Clears the phrase
DIV CH SELECT Switches between Preamp channel A and B .
OD/DS SOLO Switches the OD/DS SOLO on and off .
A/B SOLO Switches the Preamp SOLO on and off .
A&B SOLO
Switches the preamp SOLO, for both
channel A and B, on and off .
If one of the two channels is off, both will be
turned on .
COMP Switches the COMP on and off .
OD/DS Switches the OD/DS on and off .
PREAMP Switches the PREAMP/SPEAKER on and off .
EQ Switches the EQ on and off .
FX1 Switches the FX1 on and off .
FX2 Switches the FX2 on and off .
DELAY Switches the DELAY on and off .
CHORUS Switches the CHORUS on and off .
REVERB Switches the REVERB on and off .
PEDAL FX Switches the Pedal FX on and off .
SEND/RETURN Switches the SEND/RETURN on and off .
AMP CTL Switches the Amp Control on and off .
TUNER Switches the TUNER/BYPASS on and off .
MANUAL MODE Switches the MANUAL MODE on and off .
BPM TAP *1 Used for tap input of the MASTER BPM .
DELAY TAP *1 Used for tap input of the delay time .
MIDI START
Controls the Start/Stop of external MIDI
devices (such as sequencers) .
MMC PLAY
Controls the Play/Stop of external MIDI
devices (such as hard disk recorders) .
LEVEL +10 *1
Increases the patch volume level by 10
units .
LEVEL +20 *1
Increases the patch volume level by 20
units .
LEVEL -10 *1
Decreases the patch volume level by 10
units .
LEVEL -20 *1
Decreases the patch volume level by 20
units .
NUMBER INC *1
Switches to the next higher patch number
in the same bank as the currently selected
patch .
NUMBER DEC *1
Switches to the next lower patch number
in the same bank as the currently selected
patch .
BANK INC *1 Switches to the next higher bank number .
BANK DEC *1 Switches to the next lower bank number .
LED ON/OFF
Lights/extinguishes the pedal’s LED
indicator .
* This is shown only when ACCEL/CTL pedal
is selected .
* This is shown only if PERFORMANCE (p . 28)
is set to PATCH .
*1 The function will activate as soon as you press the pedal, regardless of
whether the SOURCE MODE parameter is MOMENT or TOGGLE .
Parameter Value Explanation
MIN
OFF, ON
(or STOP, START) This sets the value for times when the
switch is Off .
MAX
OFF, ON
(or STOP, START) This sets the value for times when the
switch is On .
SOURCE
MODE
This sets the behavior of the value each time the switch is
operation .
MOMENT
The normal state is Off (minimum value),
with the switch On (maximum value) only
while the footswitch is depressed .
TOGGLE
The setting is toggled On (maximum value)
or Off (minimum value) with each press of
the footswitch .
EXP, SUB EXP
Here’s how to assign the parameters that will be controlled by the GT-100’s
[EXP] pedal, and by an expression pedal (such as the separately available
EV-5) connected to the SUB CTL 1, 2/SUB EXP jack .
Parameter Value Explanation
FUNC
OFF No assignment .
FOOT VOLUME Foot volume will be assigned .
PEDAL BEND Pedal bend will be assigned .
WAH Wah will be assigned .
PB/FV Pedal bend and foot volume will be assigned .
WAH/FV Wah and foot volume will be assigned .
PATCH LEVEL
Patch level will be assigned .
* This is shown only if PERFORMANCE (p . 28) is set
to SYSTEM .
PATCH LEVEL
MIN
0–200
Specifies the minimum value .
* This is shown only if FUNC is set to PATCH
LEVEL .
PATCH LEVEL
MAX
0–200
Specifies the maximum value .
* This is shown only if FUNC is set to Patch Level .
* Only FOOT VOLUME can be assigned to SUB EXP (external expression
pedal) . If you want to assign a function other than FOOT VOLUME, use
Assign .