IDEX Health & Science MCP Process – version without Settings Menu User Manual

Page 14

Advertising
background image

MCP Process/Ismatec SA/30.07.00/CB/GP

14

Pump-head identification

In order to obtain correct
pumping and dispensing values
the individual identification code
(ID-Code) of the mounted pump-
head must be entered (

for

each of the 4 programs),
especially when a new pump is
used for the first time and each
time the pump-head is changed.

1 Power switch »OFF«

2 Keep CAL-key pressed and

switch power »ON«

3 Press

or

key till the

correct ID-Code of the
mounted pump-head is set. For
the ID-Code see the back of
the pump-head or the table on
page 46

4 Enter the correct ID-Code with

the CAL-key
(MODE display switches
automatically to TUBE I.D.)

5 Enter the correct tubing i.d.

with the

keys (see also

page 15)

6 Confirm with the CAL-key

7 Change to PROGRAM with the

MODE key and select the next
program with the CAL and

keys (confirm with CAL).

❖ Repeat procedure 1–6 till
the ID-Code(s) of the mounted
pump-head(s) and the tubing
i.d. are entered in all 4
programs.

Identification de la tête de pompe

Pour obtenir des valeurs
correctes, il faut introduire le
code d‘identification de la tête de
pompe installée (

dans

chacun des 4 programmes),
avant la première mise en
route
ou après avoir changé la
tête de pompe.

1 Interrupteur principal sur 'OFF'

2 Maintenir la touche CAL enfon-

cée. Interrupteur principal sur
'ON'

3 Presser la touche

ou

jusqu’à ce que le code ID
correct de la tête de pompe
installée clignote. Le code ID
est indiqué sur la face arrière
de la tête de pompe ou dans le
tableau à la page 46

4 Mémoriser le code ID correct

avec la touche CAL (l’affichage
du mode commute automati-
quement sur TUBE I.D.)

5 Saisir le diamètre du tube adé-

quat au moyen de les touches

(cf. également page 15)

6 Confirmer avec la touche CAL

7 Commuter sur PROGRAM avec

la touche MODE, sélectionner
le programme suivant avec la
touche CAL et les touches
(confirmer avec CAL)

❖ Répéter la procédure de 1 à
6 jusqu’à ce que le code ID de
la tête de pompe et le diamêtre
int. du tube employés soient
mémorisés dans chacun des
4 programmes.

Pumpenkopf-Identifikation

Für korrekte Pump- und Dosier-
Werte muss die richtige Pumpen-
kopf-Identifikation (ID-Code) des
jeweils montierten Pumpenkopfes
gespeichert werden (

für

jedes der 4 Programme).
Vor allem bei der ersten Inbe-
triebnahme
und nach jedem
Wechsel eines Pumpenkopfes.

1 Netzschalter »AUS«

2 CAL-Taste gedrückt halten

Netzschalter »EIN«

3

oder

Taste drücken,

bis der für den montierten
Pumpenkopf richtige ID-Code
blinkt. Für ID-Code siehe
Rückseite des Pumpenkopfes
bzw. Tabelle auf Seite 46

4 Mit der CAL-Taste korrekten

ID-Code speichern
(Mode-Anzeige schaltet autom.
auf TUBE I.D.)

5 Mit den

Tasten den rich-

tigen Schlauch-iØ eingeben
(siehe auch Seite 15)

6 Mit der CAL-Taste bestätigen

7 Mit der Mode-Taste auf

PROGRAM wechseln, mit der
CAL und den

Tasten

nächstes Programm anwählen
(mit CAL bestätigen).

❖ Vorgehen von 1–6 wieder-
holen, bis in allen 4 Program-
men der ID-Code des jeweils
verwendeten Pumpenkopfes
und der Schlauch-iØ gespei-
chert sind.

3

aus
off

ein
on

1

2

4

7

MODE

CAL

CAL

CAL

CAL

mm
rpm
Time
Time

TUBE I.D.
PUMP
DISP
PAUSE

Volume

PROGRAM
Flow rate

TOTAL

5

6

CAL

Advertising