IDEX Health & Science MCP Process – version without Settings Menu User Manual

Page 33

Advertising
background image

MCP Process/Ismatec SA/30.07.00/CB/GP

33

Analog interface

Pin 9, speed OUT
The default setting is 0–10 V

DC

,

proportionally to the motor
speed 0–240.0 rpm.
Alternatively a frequency range
from 0–7.2 kHz is available.
Alternatives with sliding switch
S2 inside the pump (see page 34)

Pin 10, +5 V

DC

About +5 V

DC

are available.

(max. current 0.5 A)

Pin 13, speed intern
Depending on how the pump is
operated, pin 13 has different
functions:

Analog interface not activated
(Normal operation, i.e. pin 2 is
open) Pin 13 serves as auto-
start function
.
If pin 13 is connected to pin 1
(GND), the pump can be started
and stopped directly from
the power supply (the power
switch must be on).

Analog interface activated
(Pin 2 on GND)
- Pin 13 open:

The rotation speed is adjusted
via pin 5 (speed IN).

- Pin 13 on GND:

The rotation speed can be
adjusted by the speed selector
on the control panel of the
pump.

Pin 14, output 1
Pin 15, output 2
Digital outputs in connection
with pin 7 (+26 V

DC

). Can only be

activated via RS232 interface;
e.g. with a software like the
ProgEdit.

Interface analogique

Pin 9, speed OUT
Le réglage d’usine par défaut est
0–10 V

DC

, proportionnel au

nombre de tours du moteur
0–240.0 t/min. Une zone de
fréquence de 0–7.2 kHz est à
disposition en alternative.
Possibilité de sélection au moyen
d’un interrupteur coulissant S2 à
l’intérieur de l’appareil (v.p. 34).
Pin 10, +5 V

DC

Environ +5 V

DC

sont à disposition

(courant maximal 0.5 A)

Pin 13, speed intern
Le pin 13 possède des fonctions
différentes en fonction du mode
d’opération:

Interface analogique non activée
(Mode d’opération normal,
c.-à-d. pin 2 ouvert) Le pin 13
a la fonction „auto-start“.
Si le pin 13 est connecté au pin 1
(GND), la pompe peut être mise
en route ou arrêtée directement
par l’alimentation électrique
(l’interrupteur principal doit être
sur ON).

Interface analogique activée
(Pin 2 sur GND)
- Pin 13 ouvert: La vitesse de
rotation doit être ajustée par le
pin 5 (speed IN).
- Pin 13 sur GND: La vitesse de
rotation peut être ajustée par le
sélecteur de vitesse sur le tableau
de commande de la pompe.

Pin 14, output 1
Pin 15, output 2
Sorties numériques en relation
avec le pin 7 (+26 V

DC

). Ne

peuvent être activées que par
l’interface RS232, p.e. avec le
logiciel ProgEdit.

Analogschnittstelle

Pin 9, speed OUT
Die werkseitige Einstellung ist
0–10 V

DC

, proportional zur

Motordrehzahl 0–240.0 min

–1

.

Alternativ steht ein Frequenz-
bereich von 0–7.2 kHz zur
Verfügung. Wahlmöglichkeit
mittels Schiebeschalter S2 im
Geräteinnern (siehe Seite 34)

Pin 10, +5 V

DC

Es stehen ca. +5 V

DC

zur

Verfügung. (max. Strom 0.5 A)

Pin 13, speed intern
Abhängig von der Betriebsart hat
Pin 13 unterschiedliche
Funktionen:

Analogschnittstelle nicht aktiviert
(Normalbetrieb, d.h. Pin 2 offen)
Hier dient Pin 13 als Autostart-
funktion
. Ist Pin 13 mit Pin 1
(GND) verbunden, kann die
Pumpe direkt über die Netzspan-
nung gestartet bzw. angehalten
werden (Netzschalter muss
eingeschaltet sein).

Analogschnittstelle aktiviert
(Pin 2 auf GND)
- Pin 13 offen:

Die Drehzahl wird über Pin 5
(speed IN) vorgegeben.

- Pin 13 auf GND

Die Drehzahl kann am
Bedienungspanel der Pumpe
eingestellt werden.

Pin 14, output 1
Pin 15, output 2
Digitale Ausgänge in Verbindung
mit Pin 7 (+26 V

DC

). Können nur

über RS232-Schnittstelle aktiviert
werden; z.B. mit einer Software
wie ProgEdit.

8 7 6 5 4 3 2 1

15 14 13 12 11 10 9

speed IN

direction

input 1

start

+26VDC

remote

input 2

GND

output 2

speed OUT

output 1

+5VDC

speed intern

Digitale Eingänge (TTL-Pegel)

Digital inputs (TTL-level)

Entrées numériques (niveau TTL)

Pin 2, remote
Pin 3, start
Pin 4, direction
Pin 6, input 1
Pin 8, input 2

Pin 13, speed intern

Analoge Eingänge

Analog inputs

Entrées analogiques

Pin 5, speed IN

0–5 V

DC

/ 0–10 V

DC

0–20 mA / 4–20 mA

Universal Ausgänge (PWM)

Universal outputs (PWM)

Sorties universelles (PWM)

Pin 14, output 1
Pin 15, output 2

Analog-Ausgang

Analog output

Sortie analogique

Pin 9, speed OUT

0-10 V

DC

/ 0-7.2 kHz

Advertising