2 laserlight commands, 3 default print formats, 2 laserlight commands 7.3 default print formats – Rice Lake 920i USB Installation Manual V5.05 User Manual
Page 75
Print Formatting
69
7.2
LaserLight Commands
Table 7-2 lists commands to operate the Stop, Go (circle or arrow) and Off display elements on a LaserLight. These
commands are used for front panel softkeys.
Table 7-2. LaserLight Commands
Traffic Light State
Aux Fmt
Dry Contact
Serial Command
Stop
AuxFmt1
Dig0 and Dig1 open circuit
|00DO3!
Green Circle
AuxFmt2
Dig0 open circuit; Dig1 pulled low
|00DO2!
Green Arrow
AuxFmt2
Dig0 pulled low; Dig1 open circuit
|00DO1!
Off
AuxFmt3
Dig0 and Dig1 pulled low
|00DO0!
7.3
Default Print Formats
Table 7-3 shows the default print formats for the 920i and lists the conditions under which each print format is
used. HDRFMT1 and HDRFMT2 specify header information that can be used by other ticket formats. The contents
of HDRFMT
x
can be inserted by using the <H1> and <H2> formatting commands.
Alert Format Commands
<COMP>
Company name (up to 30 characters)
All
<COAR1>
<COAR2>
<COAR3>
Contact company address, lines 1–3 (up to 30 characters)
<CONM1>
<CONM2>
<CONM3>
Contact names (up to 20 characters)
<COPH1>
<COPH2>
<COPH3>
Contact phone numbers (up to 20 characters)
<COML>
Contact e-mail address (up to 30 characters)
<ERR>
Alert error message (system-generated)
ALERT
See the
iQUBE
2
Installation Manual, PN 106113, for more information about using alerts.
Format
Default Format String
Used When
GFMT
GROSS<G><NL2><TD><NL>
Normal mode, no tare in system
NFMT
GROSS<G><NL>TARE<SP><T><NL>NET<SP2><N>
<NL2><TD><NL>
Normal mode, tare in system
ACCFMT
ACCUM <A><NL><DA> <TI><NL>
Accumulator enabled and displayed, or
setpoint print operation with PSHACCM=ON
SPFMT
<SCV><SP><SPM><NL>
Setpoint print operation with PSHPRNT=ON
TRWIN
<NL>ID<SP><TID><NL2>GROSS<TR1>
<NL2><DA><SP><TI><NL>
Press the Weigh In softkey, enter truck ID
number, and press enter.
TRWOUT
<NL6>ID<SP><TID><NL2>GROSS<TR1><NL>TARE<SP>
<TR2><NL>NET<SP2><TR3><NL2><DA><SP><TI><NL>
Press the Weigh Out softkey, enter truck ID
number, and press enter.
TRFMT
REG ID: <TID>: <TR2> SCALE<S> <TD><NL>
Truck register currently displayed
ALERT
<COMP><NL><COAR1><NL><COAR2><NL><COAR3><NL>
<CONM1> <COPH1><NL>
<CONM2> <COPH2><NL>
<CONM3> <COPH3><NL>
<COML><NL><ERR><NL>
Alert message is sent to specified port when
error indication is generated by an attached
iQUBE
2
. See the iQUBE
2
Installation Manual,
PN 106113, for more information.
Table 7-3. Default Print Formats
Command
Description
Supported Ticket Formats
Table 7-1. Print Format Commands (Continued)