Futaba 6J 2.4GHz User Manual

Page 41

Advertising
background image

41

7KH ³´GLUHFWLRQ LQGLFDWHV GHFUHDVLQJ DPRXQW RI PRYHPHQW WRZDUG WKH XSZDUG IURP WKH DLOHURQ VXUIDFH
ZKLOH ³´ GLUHFWLRQ LQGLFDWHV GHFUHDVLQJ DPRXQW RI PRYHPHQW WRZDUG WKH GRZQZDUG IURP WKH DLOHURQ
surface.

7) Once the mix has been activated, move the servos to their full extremes to make certain they are not

overdriving the controls. If necessary, adjust the linkages to achieve the correct control throws.

8) Press and hold the END key to exit the programming menu.

Flap trim (FLTR)- (ACRO only)

7KH )ODS 7ULP IXQFWLRQ LV XVHG WR VSHFLI\ WKH DPRXQW RI ÀDS WUDYHO SURGXFHG PRYLQJ WKH ÀDS VZLWFK 7KH
ÀDS WULP IXQFWLRQ VKRXOG EH DFWLYDWHG LI \RX ZLVK WR FRQWURO WKH ÀDSV E\ WKH ÀDS WULP FRQWURO

7KH 7- WUDQVPLWWHU DOORZV FRQWURO RI WKH ÀDS WULPV IURP WKH URWDU\ NQRE RU VZLWFKHV $ % RU '

7R DGMXVW ÀDS WULP

1) Turn the transmitter on.

2) Press and hold the MODE button to access the programming mode.

3) Press either the MODE key OR the END key to scroll through the function menus.

&RQWLQXH SUHVVLQJ WKH 02'( RU (1' NH\ XQWLO WKH ÀDS WULP )/75 PHQX DSSHDUV
on screen.

4) Push the DATA INPUT lever upward for approximately two (2) seconds. This will

FDXVH WKH ,1+ GLVSOD\ WR ÀDVK UDSLGO\ EHIRUH FKDQJLQJ WR D ÀDVKLQJ 21 GLVSOD\

 3UHVV WKH 6(/(&7 NH\ WR DFFHVV WKH WUDYHO RI WKH ÀDS VZLWFK 7KH WUDYHO YDOXHV DUH

DGMXVWDEOH EHWZHHQ 

DQG   $GMXVW WKH YDOXHV DFFRUGLQJO\ E\ SUHVVLQJ

the DATA INPUT lever upward or downward.

Note: When using switches A, B or D, it is possible to incorporate two rates- upward or downward.
$GMXVWLQJ WKH ÀDS WULP ZLWK WKH URWDU\ NQRE DOORZV IRU SURSRUWLRQDO FRQWURO

Note: ,I XVLQJ &KDQQHOV   RU  IRU WKH OHIW DLOHURQ FRQWURO WKH ÀDS WULP YDOXHV GR QRW DIIHFW WKH WUDYHO RI WKH
DLOHURQV 7KH ÀDS WULP YDOXHV ZLOO KRZHYHU FRQWURO WKH ÀDS WUDYHO LI WKH ÀDSHURQV DUH VHW XS XVLQJ FKDQQHO 
and channel 6.

 3UHVV WKH 6(/(&7 NH\ WR FKRRVH WKH ÀDS WULP DFWLYDWLRQ PHWKRGRORJ\

Advertising