Futaba 6J 2.4GHz - Manual (Page 67)

67
 ,I WKH VWXGHQW¶V UDGLR KDV D SOXJLQ 5) PRGXOH UHPRYH WKH PRGXOH
 ,I WKH VWXGHQW¶V WUDQVPLWWHU LV D 0+] FROODSVH WKH DQWHQQD DFFRUGLQJO\
5) With both transmitters off, connect the trainer cord to both radios. (On the T6J-2.4GHz the trainer jack is
located in the center of the rear of the case). Do not force the plug into the transmitter and note that the plug
LV ³NH\HG´ VR LW FDQ JR LQ RQO\ RQH ZD\
 7XUQ RQ WKH LQVWUXFWRU¶V WUDQVPLWWHU '2 127 WXUQ RQ WKH VWXGHQW¶V WUDQVPLWWHU ,W ZLOO DXWRPDWLFDOO\ ³SRZHU
XS´ EXW ZLOO QRW WUDQVPLW D VLJQDO 6HW WKH UHYHUVLQJ DQG WULPV RI WKH VWXGHQW¶V UDGLR WR PDWFK WKDW RI WKH
LQVWUXFWRU¶V ,I ERWK WKH LQVWUXFWRU DQG WKH VWXGHQW XVH 7-*+] WKH )6 IXQFWLRQ¶V VHWXS PXVW EH WKH
same in both transmitters.
 7XUQ RQ WKH UHFHLYHU VZLWFK LQ WKH PRGHO 'HSUHVV WKH WUDLQHU VZLWFK RQ WKH LQVWUXFWRU¶V UDGLR 8VH WKH
VWXGHQW¶V UDGLR WR RSHUDWH WKH FRQWUROV DLOHURQV HOHYDWRU UXGGHU HWF DQG REVHUYH KRZ WKH\ UHVSRQG 0DNH
DQ\ DGMXVWPHQWV QHFHVVDU\ WR WKH VWXGHQW¶V WUDQVPLWWHU WR JHW WKH FRQWUROV WR UHVSRQG FRUUHFWO\
 &KHFN WR VHH WKDW WKH WULPV DUH LQ ³V\QF´ E\ WRJJOLQJ WKH WUDLQHU VZLWFK EDFN DQG IRUWK D IHZ WLPHV 7KH
controls on the model should remain stationary. If the controls do not remain stationary, this indicates that
WKH WULP VHWWLQJV RQ WKH VWXGHQW¶V UDGLR GR QRW PDWFK WKRVH RQ WKH LQVWUXFWRU¶V UDGLR $GMXVW WKH VWXGHQW¶V
trims as necessary.
Note: When the instructor initially depresses the trainer switch on his transmitter, there will be approximately
a one (1) second delay before the student takes control. In most situations this momentary delay will go
unnoticed.
TIMER
The T6J offers three timers: count up, count down and model. The count up (stopwatch) and count down
timer are programmable and feature an audible alarm when the programmed time limits have been reached.
The model timer, as the name suggests, is used to track time of the model.
Countdown times sound one short beep each second during the last 10 (ten) seconds of the countdown
function and one long tone when at the programmed time. The timer will then display a minus (-) sign and
continue tracking the time.
The count up timer will also beep one short beep each second for the last ten (10) seconds and then one long
tone at the programmed time. Additionally, the count up timer will continue counting upwards, there will not
be a minus (-) sign, however.
As noted above, the model timer is used to track the time of the model. This is a count up timer and starts
when the respective model memory is selected and the T6J is powered up.