Futaba 6J 2.4GHz - Manual (Page 51)

51
Note: As with all switch selection availability, if the modeler has programmed any other functionality to this
switch selection, the idle up throttle curve and the other function will be activated simultaneously. As such, it
is imperative to ensure that these desired functions will not negatively impact one another.
For example, if the modeler has programmed Switch B to activate the low rates, and then selected Switch B
as the activation switch for the idle up curves, moving Switch B will activate both functions simultaneously.
Note: if the trainer function is activated, the switch C is allocated for the trainer function automatically.
9) Press and hold the END button to exit the programming mode.
Pitch Curve Idle UP (I-PI) - (HELI only)
7KLV IXQFWLRQ LV XVHG WR VHW WKH SLWFK FXUYH IRU LGOH XS ÀLJKW 7KH SLWFK FXUYH SURJUDPPLQJ DOORZV WKH 7-¶V
SLWFK FRQWURO WR YDU\ IURP WKDW RI D OLQHDU FRQWURO 7KDW LV WKH VHUYR SRVLWLRQ GRHVQ¶W KDYH WR PDWFK WKH LQSXW
IURP WKH WKURWWOHSLWFK VWLFN SRVLWLRQ 7KXV DOORZLQJ WKH SLWFK RSHUDWLRQ WR EH DGMXVWHG WR PHHW WKH PRGHOHU¶V
VSHFL¿F QHHGV DW YDULRXV SRLQWV LQ WKH WKURWWOH VWLFN PRYHPHQW
A 5-point pitch curve is utilized to best match the blade collective pitch to the engine RPM for consistent
load on the engine. The curve can be adjusted from 0-100% each point. Idle up creates a curve typically
XVHG IRU IDVW IRUZDUG ÀLJKW DQG DHUREDWLFV 1RUPDOO\ DQ LGOH XS FXUYH GRHV QRW DOORZ WKH HQJLQH WR LGOH GRZQ
even when the stick is pulled all the way back. This is one of the functions that makes the maneuvers such as
LQYHUWHG ÀLJKW SRVVLEOH
*HQHUDOO\ VSHDNLQJ WKH SLWFK FXUYH VKRXOG EH VHW XS DV IROORZV KRZHYHU HDFK KHOLFRSWHU ZLOO KDYH VSHFL¿F
UHFRPPHQGDWLRQV IRU WKH VW\OH RI À\LQJ \RX GHVLUH
‡ Point 1- the collective servo is at the desired lowest point with the throttle stick at the lowest (bottom)
position. This is normally full negative pitch.
‡ Point 2- the collective servo is at the desired point with the throttle stick is advanced ¼ of the way.
‡ Point 3- the collective servo is at the desired point with the throttle stick advanced ½ way.
‡ Point 4- the collective servo is at the desired point with the throttle stick advanced ¾ of the way.
‡ Point 5- the collective servo is at the desired point with the throttle stick fully advanced. This is full positive
pitch.
To set the idle up pitch curve:
1) Turn the transmitter on.
2) Press and hold the MODE button to access the programming mode. An audible
double beep will be heard and the default screen will change accordingly.
3) Press either the MODE key OR the END key to scroll through the function menus.
Continue pressing the MODE or END key until the idle up pitch curve (I-PI) menu