Futaba 14MZ - Manual (Page 78)

Setting methods
●Group/single mode selection
Activating functions for only the selected
conditions:
1. Touch the Group button and switch to the
Sngl mode.
*Each time the button is touched, it toggles between the Gr.
and Sngl modes.
●Mixing mode selection
Using the offset mode:
1. Touch the Mode button and switch to the
Offset mode.
*Each time the button is touched, it toggles between the Mix
and Offset modes.
●Mixing setup screen selection
1. Touch the button of the mixing you want
to set. The mixing setup screen is displayed.
Activate the function.
2. Activate the function by touching the [INH]
button.
*Each time this button is touched, it toggles between [INH]
and [ON/OFF].
●Mixing ON/OFF switch setting and ON/OFF
direction switching
*An ON/OFF switch is not set even when the function is
activated.
1. When you want to turn mixing ON/OFF by
switch, touch the [NULL] button to call the
<Switch> screen and then select the switch
and its ON direction.
*For a description of the selection method, see [Switch
Setting Method] at the back of this manual.
●Master channel setting (except offset type
mixing)
1. Touch the Master button to call the Function
menu and select the master channel.
2. To link this mixing with other mixing, touch the
button at the left of the master channel and
select link.
*Each time the button is touched, it toggles between mixing
direction + and - and "No display" (no link).
*Master channel control can be set to stick, VR, and other
simple travels which do not include ATV, AFR, D/R, mixing
setting, etc. In this case, display the <Switch> screen by
touching the [H/W] button and then select master channel
side control.
●Slave channel setting
1. Touch the Slave button to call the Function
menu and select the slave channel.
2. To link this mixing with other mixing, touch
the button at the right-hand side of the slave
channel and select link.
*Each time the button is pressed, it toggles between mixing
direction + and - and "No display" (no link).
●Trim mode ON/OFF setting
1. To turn the trim mode ON/OFF, touch the Trim
button on the screen.
*When mixing includes master side trim, set the Trim button
to [ON]. When mixing does not include master side trim, set
the Trim button to [OFF].
*Each time this button is pressed, it toggles between [ON]
and [OFF].
*This is effective when the master channel is set by Function.
●Slave channel AFR mode (STK→STK)
1. When Link is set at the slave side, and you
want to add AFR (D/R) to the mixing rate,
select [ON]. When you do not want to add
AFR (D/R) to the mixing rate, select [OFF].
*Each time this button is pressed, it toggles between [ON]
and [OFF].
*This is effective when making corrections when the fuselage
is the same but the rudder angles are substantially different.
●Mixing curve type selection
1. Touch the curve type selection button of the
curve type you want to use to display the
selection screen and then select the curve
you want to use.
*For a description of the curve setting method, see the
description at the back of this manual.
●Fine tuning trim setting
1. When using the curve fine tuning function,
touch the [NULL] button of the Fine Tuning
item to call the <Switch> screen and then
select the lever, VR, etc. you want to use.
*For a description of the fi ne tuning trim setting method, see
the description at the back of this manual.
●Servo speed setting
1. When setting the servo speed, touch the
Speed button. The Servo Speed setup screen
is displayed.
*For a description of the servo speed setting method, see the
description at the back of this manual.
*Offset mixing changes the speed. Use the Speed In and
Speed Out buttons to readjust the speed..
The mixing switch can set a delay with a different rate at
starting and stopping.
*This function is inactive when a mixing switch is not set.
78 <Model Menu (Common Functions)>