Ericsson EDACS LBI-39077 - Manual (Page 44)

LBI-39077 DATABASE
44
•
Phone # - (This field is not present when the local data link is selected.) This field defines the telephone number
of the subscriber line connected to a GTI unit in the system (when the internal modem is selected), or to an
external modem in the system (when the external modem is selected). (Default = Blank)
•
Baud Rate - This field defines the baud rate to be used when communicating with the system. Press the Enter
key and select the rate you want from a second pop-up window. (Default = 9600 for local, 1200 for internal
modem, and 2400 for external modem)
•
PC Comm Port - This field is used to tell the GTI Configurator which COM port will be used to communicate with
a GTI unit in the system. Enter a one-digit number from 1 to 4. (Default = 1)
•
Use Auto Time Set? - This field is used to determine if you want the GTI Configurator to automatically set the time
in the GTI units in the system (enter Y), or if you want to manually set the time when connected to the system (enter
N). (Default = Y) If you enter a Y, a TIME_SET pop-up window will appear displaying the following two additional
fields:
•
Hours Difference: - This field is used to define a time zone correction between the GTI Configurator’s location
and the system’s location. Enter a two-digit number from 1 to 12 (hours). (Default = 00)
•
Earlier or later in relation to this time zone?: - This field is used to define if the system’s time is to be earlier
than (enter an E), later than (enter an L), or the same as (enter an S) the GTI Configurator’s time. (Default = S)
•
Disconnect on 2nd Dial Tone - This field is used to define whether you want the GTI unit hang up when it detects a
second dial tone. Enter a Y if you want the GTI unit to treat a second dial tone as a telephone hang-up. Enter an N if
radio-originated calls will be calling into a system that gives a second dial tone as a prompt for additional dialing.
(Default = Y)
•
Dial Tone Required - This field is used to define if the GTI unit must detect dial tone before dialing or not. If you
enter Y for yes, the GTI unit will dial out only after detecting dial tone. If you enter N for no, the GTI unit will dial
out as soon as it detects dial tone, or as soon as the dial tone seek time is up. (Default = Y) If you enter an N, a
DT_SEEK pop-up window will appear displaying the following additional field:
•
Dial Tone Seek Time: - This field is used to define the amount of time in seconds that the GTI will wait for a
dial tone before starting to dial out anyway. Enter a number from 00.0 to 20.0. (Default = 00.5)
•
Min. Call Time to Store - This field is used to define the time in seconds that a call must be in progress before it is
stored as a Call Detail record. This feature can be used to save call detail storage space by not storing incomplete and
erroneous calls. Enter a number from 0 to 999. (Default = 020)
•
Should Interconnect continue, when billing data is lost - This field is used to define whether you want the system
to continue processing interconnect calls after the GTI detects a problem with support hardware and it becomes
unable to store Call Detail records. Enter Y for yes, N for no. (Default = Y)
• •
Narrowband - 12.5 kHz? - This field is used to define whether narrowband MASTR II repeaters are being used in
the system (so that repeater audio levels will be set correctly). Enter Y for yes, N for no. (Default = N)
•
Edit Voice Prompts - This field is used to define if you want to edit the current voice prompts. Enter Y for yes, N
for no. (Default = Y) If you enter a Y, a PROMPTS pop-up window will appear displaying the following additional
fields:
•
Security Code: - This field is used to define the security code that must be overdialed when accessing voice
prompt programming from a telephone. Programming is not enabled if the overdialed value is incorrect. Applies
for all line types. Enter a number from 0000 to 9999, or leave blank to disable the security code requirement.
(Default = blank)
•
Use - This field (for each prompt message) is used to define what type of prompt it is. Enter N for no prompt, T
for a tone prompt, and V for a voice prompt. If V is entered for a voice message that is not programmed, the
tone message will be given in its place. (Default = V for messages 1 through 6, and T for message 7)