Ericsson EDACS LBI-39077 - Manual (Page 47)

DATABASE LBI-39077
47
as 24-hour time in hours and minutes. The number will be called every 24 hours at the given time. (Default is
none.)
• •
Edit C.O. Numbers: - This field is used if you want to enter telephone numbers for the hybrid balance and adjust
level operations. Enter N if you don’t; Y if you do. (Default is N.) If you entered a Y, the CO_NUMBERS pop-up
window will appear displaying the following two additional fields:
•
Silence Number: - This field is used to store the telephone number (up to 12 digits) of a device that will
automatically answer and provide a “quiet termination” for the hybrid balance operation. (Default is none.)
•
Milliwatt Number: - This field is used to store the telephone number (up to 12 digits) of a device that will
automatically answer and provide a 1 milliwatt test tone level for the level adjustment operation. (Default is
none.)
•
Telco Line Type: - This field is used to define the telephone line type. Enter N for none, E for End-to-End, D for
DID, or M for E&M. Although the GTI unit will override this selection if it is incorrect, the related line parameters
will not be used, and the GTI's defaults will be used instead. To avoid confusion, set this value to the appropriate line
type. (Select the Monitor operation in the Comm group to view the line types. Press the Print Screen key to make a
copy if a printer is connected.) (Default is E.) If you enter an E, D, or M, a pop-up window will appear displaying the
following additional fields:
If you entered an E for End-to-End:
•
Line Supervision Type: This field selects L - Loop start, or G - ground start for this line.
•
End of Call Conditions: If the C.O. provides battery you can select disconnect on battery removal if you
choose 'Y'. Select 'N' if no battery is available.
•
Dial Click Decode Mode: If you don't want to decode dial clicks this field must be set to 'N'. DTMF will always
be decoded, regardless of the setting of this field. The available choices are:
N Dial Click not enabled.
0 Decode clicks Mode 0.
1 Decode clicks Mode 1.
2 A leading '0' is required to calibrate the software.
3 A leading '0-1' are required to calibrate the software.
•
Connect Time Required: This field programs the amount of time the connect signal must be stable to recognize
the start of an incoming call. This should be set to about 0.5 sec for End-End, and to about 0.06 for DID and
E&M. (Range: 0 - 2.50, Default: 0.5)
•
Delay Before Prompt: Enter the number of seconds to delay after supervision detected before prompts are
played (voice or tone).
•
Dial-Out Mode: Choose the dial out method, 'D' for DTMF dialing, 'P' for pulse dialing, 'M' for MF dialing.
If you entered a D for DID:
•
Line Supervision Type: This field selects the type of supervision of the incoming DID line. This information
should be provided by the phone company when the line is purchased. "I" indicates Immediate Start - the C.O.
sends feed digits immediately after the line is answered, "W" indicates Wink Start - the C.O. waits until the GTI
unit "winks" the line before sending the feed digits. (Range: I, W, Default: I)
•
Signaling Type: This field selects the type of signaling used by the C.O. to send the feed digits to the GTI unit.
The available choices are: D - DTMF, P - Pulse, or M - MF. (Range: D, M, P, Default: D)
•
Number of Feed Digits: This field selects the number of feed digits expected from the C.O. (Range: 2-4,
Default: 2)
•
Connect Time Required: This field programs the amount of time the connect signal must be stable to recognize
the start of an incoming call. This should be set to about 0.5 sec for End-End, and to about 0.06 for DID and
E&M. (Range: 0 - 2.50, Default: 0.5)