Loading the data using scsi, Saving all programs (save all), Press the execute/yes key (“save” light up.) – Fostex D-108 User Manual
Page 98: The d-108 will enter the setup mode
D-108 Owner's Manual (Saving and Loading Song Data)
98
44.1kHz
SETUP
SAVE
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
SAVE
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
SAVE
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
Saving all Programs (Save ALL)
1.Follow Steps 1 through 5 of the “Saving an
individual Program” procedure.
2.Use the JOG dial to select “Save ALL?” (“?”
flashes.).
Selecting “Save All?” will cause the following display to
appear.
This indicates the number of ALL the programs being
saved and the actual number of programs that can be
saved. The number on the right side of (**/**) indicates
the total number of programs existing, and the number
on the left side indicates the number of programs that
can be saved.
Therefore, when the numbers on the left and right are
equal then all the programs can be saved, as shown in
the case above. However, you must note the following
indications that are individually described.
“03/05” means that three Program out of five Programs
can be saved.
“00/05” means that no Programs can be saved. If you
press the EXECUTE/YES key at this point, “Void
Command!” appears and you cannot proceed with the
save operation.
<Note>
If you have selected “Save All”, you cannot use multiple
disks to save.
In this case, chose the save operation for an individual
Program.
3.Press the EXECUTE/YES key (“SAVE” light up.)
The save process is started and save is taking place serially
from Program 1. "COMPLETED!" lights up when the
program is successfully saved.
4.Press the STOP button or the EXIT/NO key to return
to the previous Time Base display.
Loading the data using SCSI
Here you are loading on the current drive, the data of each program or the data of all programs saved on the
backup purpose SCSI hard disk. The prerequisite is that the current drive is an E-IDE hard disk, as in the case
of save procedures mentioned earlier, and that a backup SCSI hard disk is connected to the D-108.
Load the program with the "Load PGM?" menu in the SETUP mode. This assumes that a saved disk is inserted
in the backup purpose SCSI hard disk.
Load the data saved on one removable disk (or fixed disk).
* Input format available:
adat, DAT, SCSI 6
* Programs available:
P01 - P99, or All Program
* Track available:
When using an adat or DAT: Tracks 1-8, Tracks 1-16, Tracks 1-24, Tracks 9-16,
Tracks 9-24, Tracks 17-24;
When using a SCSI disk: All tracks will be automatically selected.
1.Press the DISP SEL key to select “SETUP”
(“SETUP” will flash) and press the EXECUTE/YES
key. (“SETUP” will light up.)
The D-108 will enter the Setup mode.
2.Use the JOG dial to select “Load PGM?” (“?” will
flash.).
3.Press the EXECUTE/YES key. (“LOAD” will light.)
An indication of the type of the digital signal to be loaded
will flash on the display.
<Note>
You cannot abort a load operation on a SCSI device
while it is in progress.
44.1kHz
SETUP
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
44.1kHz
SETUP
LOAD
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞