KORG Electronic Keyboard - Manual (Page 123)

Program P7: KARMA 7–6: Perf Real-Time Parameters
113
A ( Module A) [Off, On]
Specifies the module to which the settings of RT Parm
1–8 will apply. In Program mode, only one KARMA
Module (module [A]) can be used. Thus in Program
mode, you can turn the RT Parm 1–8 settings on/off.
On (checked): RT Parm settings will be valid.
Off (unchecked): RT Parm settings will be ignored.
Assign [---, Slider1…8, Slider (SW) 1…8,
SW1…8, DynaMIDI1…8]
Assigns the selected parameter to a controller. If you
assign a parameter to KARMA Real-Time Controls ,
you can control it in real-time while you play.
For more information, see “ASSIGN” on page 111.
Polarity [+, –]
Specifies the polarity used when you operate the
KARMA Real-Time Controls that you selected for
“Assign.”
For more information, please see “POLARITY” on
page 111.
Group: PE (Performance)
Time Signature [+0000…+0048]
Assigns the “KARMA T.Sig” (Program 7–1a) function.
+0000: Off
+0001…+0048: Corresponds to 1/4–16/16.
For more information, see “KARMA T.Sig (Time
Signature)” on page 99.
If you select Time Sig. as a parameter for
assignment, you will not be able to set “A (Parm
Module A).”
Group: Mix
Transpose [–0036…+0036]
Assigns the “Transpose” (Program 7–3b) function.
Control the transposition in semitone steps.
Transpose Octave [–0036…+0036]
Assigns the “Transpose” (Program 7–3b) function.
Control the transposition in octave steps.
Transpose Octave/5th [–0036…+0036]
Assigns the “Transpose” (Program 7–3b) function.
Control the transposition in steps of an octave and a
fifth.
Group: Control
Force Range [+0000…+0004]
Assigns the “Force Range” (Program 7–3b) function.
+0000: Off
+0001: Lowest
+0002: Highest
+0003: C3–B3[1]
+0004: C3–B3[2]
For more information, see “Force Range” on page 103.
Force Range Wrap [+0000…+0011]
Assigns the “Force Range Wrap” (Program 7–3b)
function.
+0000: C…0011: B
For more information, see “Force Range Wrap” on
page 104.
Root Position [+0000, +0001]
Assigns the “Root Position” (Program 7–3b) function.
+0000: Off
+0001: On
For more information, see “Root Position” on page 104.
Clock Advance Mode [+0000…+0003]
Assigns the “Mode (Clock Advance Mode)” (Program
7–3b) function.
+0000: Auto
+0001: Dyn
+0002: Auto+Dyn1
+0003: Auto+Dyn2
For more information, see “Mode” on page 105.
Clock Advance Size [+0000…+0011]
Assigns the “Size (Clock Advance Size)” (Program 7–
3b) function.
+0000…+0010: 3…
+0011: Event
For more information, see “Size” on page 105.
CA Vel. Sensitivity [+0001…+0127]
Assigns the “Velocity Sense Bottom” (Program 7–3b)
function.
For more information, see “Velocity Sense Bottom” on
page 106.
CA Chord Trigger Mode [+0000…+0004]
Assigns the “Chord Trigger Mode” (Program 7–3b)
function.
+0000: Off
+0001: 1st
+0002: Chrd1
+0003: Chrd2
+0004: Chrd3
For more information, see “Chord Trigger Mode” on
page 106.
Note Map Mode [+0000…+0003]
Assigns the “Mode (Note Map Mode)” (Program 7–3b)
function.
+0000: Off
+0001: On-Main
+0002: On-Repeat
+0003: On-All
For more information, see “Mode (Note Map Mode)”
on page 106.