KORG Electronic Keyboard User Manual

Page 543

Advertising

Sequencer: Page Menu Commands Auto HDR/Sampling Setup

533

S/P DIF IN jack will be input to the OASYS. (0–8a
“Audio Input”)

3. Use “Mono-L/Mono-R/Stereo” to select the input

source and the number of channels you will
sample.
The Mono-L setting will sample from Audio Input1,
3 and S/P DIF L to sample to L-MONO, Mono-R
will use Audio Input2, 4, and S/P DIF R to sample
to R-MONO, and Stereo will use Audio Input 1/2,
3/4, and S/P DIF L/R to sample in stereo.

4. Use the “To” field to select the track that you will

use for In-Track Sampling.
Note data will automatically be written to the track
you select.

5. Use “Program” to specify the program into which

the sample will be converted.
When sampling ends, the entire process of creating
a new multisample through converting it to a
program and assigning it to a track will be
performed automatically.

6. Press the OK button to execute the command. If

you decide not to execute, press the Cancel button.
For more information, see “Auto HDR/Sampling
Setup: Automatically-set parameters and their
values” on page 533.

In-Track Sampling after you execute this command

1. Use “Location” to specify the location from which

you want the song to play back.

2. Press the SAMPLING REC switch to enter

sampling-standby mode.

3. Press the SEQUENCER START/STOP switch to

begin playback.

4. At the point where you want to start sampling,

press the SAMPLING START/STOP switch. In-
Track Sampling will begin.

5. Play the instrument etc. that is connected to the

AUDIO INPUT jack you selected as the “Source
Audio” setting.

6. When you’re finished playing, press the

SAMPLING START/STOP switch to stop only
sampling.
If you press the SEQUENCER START/STOP switch,
both sampling and song playback will stop.

Note: If you continue sampling after executing In-
Track Sampling, successive samples will
automatically be assigned to C#2, D2, … etc.
However if you execute Auto Sampling Setup once
again and then sample, the samples will be created
in a new multisample.

Auditioning the data you sampled

• Return the “Location,” and then press the

SEQUENCER START/STOP switch to play back
the song.

Alternatively, use Track Select (0–1a) to select the
track you specified in “To” (dialog box), and play
the C2 key.

An example of changing the settings

• If you want to apply an insert effect to the input

source, go to the Sequencer P0: Audio In/Sampling
page and set “Bus (IFX/Indiv.) Select” to IFX1–
IFX12. Set the Bus Select following the insert effect
you’re using to REC 1/2.

• To change the way in which sampling is initiated,

change the “Trigger” setting. If you set this to
Threshold, resampling will begin the instant the
input level exceeds the specified value.
Use the page menu command Select Sample No. to
select the sampling-destination RAM memory.

• If you selected S/P DIF for “Source Audio,” you

may also wish to check that the Global System
Clock parameter is set appropriately. For more
information, see “System Clock” on page 644.

Auto HDR/Sampling Setup: Automatically-set parameters and their values

Initialize

HDR (Audio

Track Recording)

Bounce Audio

Track

2ch Mix to

Disk

Resample

SEQ Play

In-Track

Sampling

Input (Input Source)

Input1…4
S/P DIF

[Source Audio]

Input1…4
S/P DIF

[Source
Audio]

Input1, 3,
S/P DIF-L

Bus Select

Off

[IFX]

Off

FX Ctrl Bus

Off

REC Bus

Off

1/2

Send1/2

000

Pan

L000

Level

127

Input2, 4,
S/P DIF-R