Track 02…16 (track number), 1–1: page menu commands – KORG Electronic Keyboard User Manual
Page 461
Sequencer P1: EQ/Vector/Controller 1–1: MIDI Track EQ
451
Regardless of this setting, subsequent edits to the
Program’s EQ in Program mode will not affect the
Combination.
On: the Program’s EQ settings will be loaded
automatically along with the Program. This is the
default setting.
Off: the Program’s EQ settings won’t be loaded. Use
this if you’ve set up the EQ in a specific way, and then
want it to stay unchanged while you try out different
Programs.
Bypass
[Off, On]
If this is On (checked), all of the EQ will be disabled,
including “Input Trim.” Bypass can be convenient for
comparing the results of the EQ with the original
signal.
Input Trim
[00…99]
This controls the volume level going into the EQ. Note
that this parameter uses a linear scale; 50 is equivalent
to –6dB, 25 is the same as –12dB, and so on.
High settings of the Low, Mid, and High Gain controls
can cause substantial increases in the overall level. You
can compensate for this by turning down the input
trim.
High Gain
[–18.0…+18.0dB]
This controls the gain of the 10kHz High Shelf EQ, in
increments of 0.5dB.
Mid Frequency
[100Hz…10.00kHz]
This sets the center frequency for the Mid sweep EQ.
Mid Gain
[–18.0…+18.0dB]
This controls the gain of the Mid Sweep EQ, in
increments of 0.5dB.
Low Gain
[–18.0…+18.0dB]
This controls the gain of the 80Hz Low Shelf EQ, in
increments of 0.5dB.
MIDI Track EQ and the control surface
You can use the Control Surface to adjust almost all of
the Track EQ parameters (except for Bypass). To do so:
1. Press the CONTROL ASSIGN MIXER
TIMBRE/TRACK switch to select either Tracks 1–8
or 9–16.
2. Use the MIX SELECT 1/9–8/16 switches to select
the Track you want to control.
3. Press the MIXER KNOBS switch to select
CHANNEL STRIP.
4. Use the MIX CHANNEL STRIP knobs 2-6 to
adjust the EQ TRIM, LOW EQ gain, MID EQ
frequency and gain, and HIGH EQ gain, as
desired.
Track 02…16 (Track Number)
These parameters adjust the three-band EQ (with
sweepable mid range) for MIDI tracks 2 through 16.
They are the same as for track 1. See “Track 01”:.
▼ 1–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see “ENTER + 0-9: shortcuts for menu
commands” on page 138.
• 0: Memory Status. For more information, see
• 1: Exclusive Solo. For more information, see
• 2: Rename Song. For more information, see
• 3: Delete Song. For more information, see “Delete
• 4: Copy From Song. For more information, see
• 5: Load Template Song. For more information, see
“Load Template Song” on page 524.
• 6: Save Template Song. For more information, see
“Save Template Song” on page 525.
• 7: FF/REW Speed. For more information, see
• 8: Set Location (for Locate Key.) For more
information, see “Set Location (for Locate Key)” on
page 525.
• 9: GM Initialize. For more information, see “GM
• 10: Copy From Combination. For more
information, see “Copy from Combination” on
page 526.
• 11: Copy From Program. For more information, see
“Copy From Program” on page 526.
• 12: Show EQ Graphic. For more information, see