KORG KPC-1 EFG - Manual (Page 25)

25
padKONTROL Owner’s Manual
3
If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ Release Value
You can specify the value of the MIDI message that will be
transmitted when you take your finger off of the X-Y pad. This
is convenient when (for example) you want to return the pitch
bend to a value of zero when you take your finger off the pad.
1
Press the [REL. VAL./LOWER] key.
The [REL. VAL./LOWER] key will light, and the display will
indicate the value of the MIDI message.
2
Use the encoder to specify the value of the MIDI mes-
sage.
If you selected Pitch Bend
Release Value [-128...0...127]
If you selected After Touch or Control Change
Release Value [0...127]
3
If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ Velocity
This parameter cannot be set for this controller. If you press
the [VELOCITY/UPPER] key, the display will indicate “ ”.
■ USB-MIDI Port
This parameter cannot be set for this controller. If you press
the [PORT] key, the display will indicate “ ”. Instead, the
messages will be transmitted according to the USB-MIDI trans-
mit port specified for each trigger pad and/or pedal that is en-
abled for the X-Y pad.
Assignable Knob 1/2 settings
You can specify the MIDI messages or parameters that will be
controlled by the two assignable knobs. In addition, you can
choose which of the trigger pads (or the pedal) will be affected
by the assignable knobs.
If you want to keep the changes you made, you must save them. If
you turn off the power or switch to a different scene before saving,
your changes will be lost. (p.15 “Saving a scene”)
■ Selecting the trigger pads and/or pedal that
will be affected by assignable knobs 1/2
For each trigger pad (and the pedal), you can specify whether
assignable knobs 1/2 will be enabled.
1
To assign settings to assignable knob 1, hold down the
[KNOB 1 ASSIGN] key. To assign settings to assignable
knob 2, hold down the [KNOB 2 ASSIGN] key.
2
The trigger pads and/or [PEDAL] key that are lit will be
affected by assignable knobs 1/2. Press the trigger pads
or the [PEDAL] key that you want to enable, making the
trigger pads or the [PEDAL] key light.
■ Assigning messages
You can specify the MIDI messages that will be transmitted
when you operate assignable knobs 1/2.
1
Press the [NOTE/CC#/LEFT] key.
The [NOTE/CC#/LEFT] key will light.
2
Use the encoder to choose the MIDI message that will be
transmitted.
No Assign ( )
Nothing will be transmitted.
Pitch Bend ( )
Pitch Bend messages will be transmitted.
AfterTouch ( )
Aftertouch messages will be transmitted.
Control Change Number [0...127]
Control Change messages of the specified number will be
transmitted. (p.115 “MIDI Control Change Messages”)
3
If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The [SETTING/ENTER] key will go dark, and you will re-
turn to Play mode.
■ MIDI Channel
This parameter is not available when assigning MIDI messages
to the assignable knobs. If you press the [MIDI CH/RIGHT]
key, the display will indicate “ ”. Instead, messages will be
transmitted on the MIDI channels that are assigned to the trig-
ger pads (and the [PEDAL] key) that have are selected to be
affected by assignable knobs1/2.
■ Polarity
You can invert the values of the MIDI messages assigned to
assignable knobs 1/2.
1
Press the [SW TYPE] key. The [SW TYPE] key will light.
2
Use the encoder to select the polarity.
Normal ( )
The polarity will be normal. The value will be lower as you
turn assignable knob 1/2 toward the left, or higher as you
turn the knob toward the right.
Reverse ( )
The values will be reversed, high to low. The value will be
higher as you turn assignable knob 1/2 toward the left, or
lower as you turn the knob toward the right.
3
If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The [SETTING/ENTER] key will go dark, and you will re-
turn to Play mode.
■ Release Value