Document Outline

• Table of Contents
  • Appendix A Calibration solutions 93
  • Appendix B Concentration curves 97
  • Appendix C Passcode editor 105
  • Appendix D ATEX safety instructions 107
• Section 1 Specifications
• Section 2 General information
  • 2.1 Safety information
    • 2.1.1 Use of hazard information
    • 2.1.2 Precautionary labels
  • 2.2 General product information
    • 2.2.1 Product overview
    • 2.2.2 FDA 21 CFR part 11 compliance (HART only)
      • 2.2.2.1 Electronic signatures for si792(x) E/T transmitters
      • 2.2.2.2 Audit trail for si792(x) E/T transmitters
• Section 3 Installation
  • 3.1 Hazardous location installation
    • 3.1.1 ATEX safety information
  • 3.2 Unpacking the transmitter
  • 3.3 Mechanical installation
    • 3.3.1 Transmitter assembly
    • 3.3.2 Mounting
      • 3.3.2.1 Wall mount
      • 3.3.2.2 Panel or pipe mount (optional)
  • 3.4 Wiring Safety Information
  • 3.5 Electrical installation
    • 3.5.1 Wire preparation
    • 3.5.2 Power and communication connections
      • 3.5.2.1 si792(x) E/T (4-20 mA/HART) wiring
      • 3.5.2.2 si792x E/T-FF and si792x E/T-PA wiring
    • 3.5.3 Sensor wire connections
      • 3.5.3.1 Hach GLI 3700 series sensor wiring-si792(x) E
      • 3.5.3.2 7MA2200 series sensor wiring-si792(x) T
      • 3.5.3.3 8398 series sensor wiring-si792(x) T
  • 3.6 HART communication connection
• Section 4 Interface and navigation
  • 4.1 si792(x) E/T (4-20 mA/HART) interface
  • 4.2 si792x E/T-FF and si792x E/T-PA interface
  • 4.3 Display
• Section 5 Operation-4-20 mA/HART
  • 5.1 Measure mode
  • 5.2 Configuration
    • 5.2.1 Current output configuration
      • 5.2.1.1 Time constant of output filter
      • 5.2.1.2 Output signal during errors
      • 5.2.1.3 Output signal during HOLD
    • 5.2.2 Temperature compensation configuration
    • 5.2.3 Alarm settings
• Section 6 Operation-Foundation Fieldbus
  • 6.1 Configuration
    • 6.1.1 Configuration steps
    • 6.1.2 Configuration menu
  • 6.2 Foundation Fieldbus communication
    • 6.2.1 Standard resource block (RB)
    • 6.2.2 Standard analog input block (AI)
      • 6.2.2.1 Operating modes
      • 6.2.2.2 Set the parameter and units
      • 6.2.2.3 Data processing
      • 6.2.2.4 Alarms
      • 6.2.2.5 Bus parameters for the analog input block
      • 6.2.2.6 Cyclic measured value status
      • 6.2.2.7 Measured value limits-limit bits
    • 6.2.3 Transducer block
    • 6.2.4 Calibration via Foundation Fieldbus
• Section 7 Operation-Profibus PA
  • 7.1 Configuration
    • 7.1.1 Configuration steps
    • 7.1.2 Configuration menu
  • 7.2 Profibus PA communication
• Section 8 Calibration
  • 8.1 Calibration
    • 8.1.1 Enter cell constant
    • 8.1.2 Calibration with a calibration solution
    • 8.1.3 Calibration by comparison/grab sample
    • 8.1.4 Zero calibration-air
    • 8.1.5 Zero calibration-calibration solution
  • 8.2 Temperature sensor adjustment
• Section 9 Maintenance
  • 9.1 Cleaning the instrument
  • 9.2 Sensor maintenance
• Section 10 Troubleshooting
  • 10.1 Sensoface
  • 10.2 Sensocheck
  • 10.3 Error codes
  • 10.4 Diagnostic tests
• Section 11 Replacement parts
  • 11.1 si792 transmitter versions
  • 11.2 Accessories
  • 11.3 Replacement parts
• Section 12 Contact information
• Section 13 Warranty, liability and complaints
• Appendix A Calibration solutions
• Appendix B Concentration curves
  • B.1 Concentration measurement ranges
  • B.2 Sodium chloride solution -01- NaCl
  • B.3 Hydrochloric acid -02- HCl
  • B.4 Sodium hydroxide solution -03- NaOH
  • B.5 Sulfuric acid -04- H2SO4.
  • B.6 Nitric acid -05- HNO3.
• Appendix C Passcode editor
• Appendix D ATEX safety instructions
• Index
  • A
  • C
  • D
  • E
  • F
  • H
  • I
  • L
  • M
  • N
  • P
  • S
  • T
  • W