LEDGlow Single Color Slimline Truck LED Underbody Kit User Manual
Page 2
8.
Next, mount the driver’s side 48 inch tube towards the front of your vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear of the truck for the 24 inch tube for the driver’s side. A good mounting location for
this tube is either to the pinch well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and do
not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody
tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the underbody tube
to the mounting bracket.
9.
Now, mount the driver’s side 24 inch tube towards the rear of the truck, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
10. Next, mount the rear 36 inch tube to the vehicle using the included mounting brackets and zip ties. Be extremely aware of the
location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8
inches between the exhaust and the underbody tube. Keep the tube and power wire away from any moving parts. Use the
included zip ties to secure the underbody tube to the mounting bracket.
11. Then, mount the passenger’s side 48 inch tube towards the front of the vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear truck for the 24 inch tube. A good mounting location for this tube is either to the pinch
well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and do not mount the underbody
tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the
power wire away from any moving parts. Use the included zip ties to secure the underbody tube to the mounting bracket.
12. Next, mount the passenger’s side 24 inch tube towards the rear of the truck, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
13. Mount the underbody kit’s ON/OFF switch in a safe and secure location inside of your vehicle. Run the lead power wire from
the front underbody tube through a pre-existing hole with a grommet in your firewall to the power switch. If you do not have a
pre-existing hole in your firewall, you can drill one, but just be sure to add a rubber grommet to ensure the lead wire is not cut or
pinched.
14. This underbody kit’s ON/OFF power switch can be powered one of two ways:
Connect the red power wire to any 12 volt source. If you need to extend the power wires, be sure to only use 16 or 18
gauge automotive grade wire. If you are running the power wire to the battery, it must go through the firewall by using an
existing grommet or by drilling a hole and adding a new grommet, which is available at any auto parts store. Be sure to
install a fuse within 6 inches of the power source.
This underbody kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box,
we recommend using LEDGlow’s Expandable Circuit, which is available a
15. Connect the black wire to a good, unpainted metal surface. A few good ground sources can be found under the dash at any main
bracket or grounding block, the negative terminal of your battery or any engine ground.
16. Beginning with Tube A, connect each tube to the next by using the modular connectors. Make sure to secure the wires tightly
when going around the suspension and/or exhaust. Leave at least 8 inches between the exhaust and underbody tube.
17. Once all of your connections have been made, and you have tested the kit to ensure all connections are secure, seal each
connection by using the included self-sealing. This ensures the connections will not get wet and cause your kit to fail.
18. It is imperative to make sure that the wires are not mounted to any direct heat source or to any moving parts. Any excess length
on the tube power wire will have to be bound up and secured tightly with zip ties.
19. DO NOT SHORTEN OR CUT ANY OF THE UNDERBODY TUBE WIRES. THIS WILL DESTROY THE KIT AND
VOID ALL WARRANTIES.
20. Lower the vehicle if it was raised, power the kit and test it for full functionality.
21. Once the vehicle is on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and/or wires
are not coming in contact with your tires or any other moving parts.
For accessories, replacement parts and/or technical support, please visi
or more information.