LEDGlow 7 Color Slimline Truck LED Underbody Kit User Manual
Page 2
6.
First, mount the front 36 inch tube to your vehicle, with the male connector facing the driver’s side, using the included mounting
brackets and zip ties. Make sure the tube is at least 8 inches away from any direct heat source and away from all moving parts.
Use the included zip ties to secure the underbody tube to the mounting bracket. IMPORTANT: DO NOT MOUNT THE
TUBE TO THE RADIATOR.
7.
Next, mount the driver’s side 48 inch tube towards the front of your vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear of the truck for the 24 inch tube for the driver’s side. A good mounting location for
this tube is either to the pinch well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and do
not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody
tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the underbody tube
to the mounting bracket.
8.
Now, mount the driver’s side 24 inch tube towards the rear of the vehicle, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
9.
Next, mount the rear 36 inch tube to the vehicle using the included mounting brackets and zip ties. Be extremely aware of the
location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8
inches between the exhaust and the underbody tube. Keep the tube and power wire away from any moving parts. Use the
included zip ties to secure the underbody tube to the mounting bracket.
10. Then, mount the passenger’s side 48 inch tube towards the front of the vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear of the truck for the 24 inch tube for the passenger’s side. A good mounting location
for this tube is either to the pinch well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and
do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody
tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the underbody tube
to the mounting bracket.
11. Next, mount the passenger’s side 24 inch tube towards the rear of the vehicle, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
12. Note: 3 brackets are provided for each tube, one for each end and an additional one for the middle of the tube. For a tight fit, you
may want to place a very thin layer of the self-sealing tape on the end of each tube and secure the bracket around it to prevent
any possible slippage while your vehicle is in motion.
13. Mount the underbody kit’s control box in a safe
and secure location inside of your vehicle. Run the lead power
wire from the front underbody tube through a pre-existing hole
with a grommet in your firewall to the control box. If you do not
have a pre-existing hole in the firewall you can drill one, just be
sure to use a rubber grommet to ensure the lead wire is not cut or
pinched.
14. This underbody kit can be powered one of two
ways:
a)
Connect the red power wire to any 12 volt source. If
you need to extend the power wires, be sure to only use 16 or 18
gauge automotive grade wire. If you are running the power wire
to the battery, it must go through the firewall by using an existing
grommet or by drilling a hole and adding a new grommet, which
is available at any auto parts store. Be sure to install a fuse within
6 inches of the power source. If you connect the power wire to a
switched 12 volt source, the underbody kit may not remember the
color and pattern it was last on before turning the vehicle off. If
you connect the power wire to a constant 12 volt source, the
underbody kit will remember the last color and pattern it was on
prior to powering the vehicle down.
b)
This underbody kit can also be powered directly from
your vehicle’s fuse box. If you are powering the kit via the fuse
box, we recommend that you install the wire using LEDGlow’s
Expandable Circuit, which is available a
15. Connect the black wire to a good, unpainted ground source. A couple of good ground sources are under the dash at any main
bracket or grounding block, the negative post on your battery, or any engine ground.