Watlow Series 96 - Manual (Page 20)

Chapter
Five
Features
The System
5 . 1 ■ F e a t u r e s Wa t l o w S e r i e s 9 6
5
Custom Menu
(patented)
The Custom Menu provides you with a shortcut to
monitor, tune or change the parameter values that
you use most often. You can go directly to the
Custom Menu in the Home Page by pressing ‰. This
provides a fast and convenient way to monitor and
change settings.
You can create your own Custom Menu with as
many as 16 of the active parameters from the list
below. When a parameter is placed in the Custom
Menu it is accessible through both the Custom
Menu and its original menu. If you change a param-
eter in the Custom Menu it is automatically
changed in its original menu. If you change a
parameter in its original menu it is automatically
changed in the Custom Menu.
If you do not assemble a Custom Menu, four default
parameters will automatically appear in the Custom
Menu.
To change the list of parameters in the Custom
Menu, press both the ‰ and ˆ keys for 6 seconds.
This will take you to the Factory Page. The Custom
Menu [CUSt] is the first menu on the Factory page.
Press the ‰ key once to go to the first selection in
the menu. The parameter choices will appear in the
top display and the selection number will appear in
the bottom display. Use the ¿ or the ¯ key to
change the selected parameter in the top display. If
you do not want a parameter to appear for that loca-
tion, select [nonE]. To change the other 15 selec-
tions, press ‰ to select a place in the menu, [``P1]
to [`p16], in the bottom display and use the ¿ or
the ¯ key to change the parameter selected in the
top display.
¯
[CUSt] Custom Menu
[FctY] →
‰
[Fcty] Factory Page
[``P1] Parameter 1 ’
•
•
[`P16] Parameter 16
¿
[nonE] →
[``P1]
[`LOC] Lockout Menu
[dIAg] Diagnostics Menu
[cin1] Calibration 1 Menu
[cin2] Calibration 2 Menu
[cout] Process Output Calibration Menu 1
[nonE] No Parameter *
[`Pr2] Process 2
[Pcnt] Percent Output *
[rPSP] Ramping Set Point
[E`St] Event Input Status
[A-M] Operation Mode *
[`Aut] Auto-tune *
[AtSP] Auto-tune Set Point
[`SP2] Set Point 2
[E`SP] Event Set Point
[`L-r] Local or Remote Mode
[CAL1] Calibration Offset *
[Pb`1] Propband 1
[It`1] Integral 1
[dE`1] Derivative 1
[rE`1] Reset 1
[rA`1] Rate 1
[Ct`1] Cycle Time 1
[db`1] Dead Band 1
[Pb`2] Propband 2
[It`2] Integral 2
[dE`2] Derivative 2
[rE`2] Reset 2
[rA`2] Rate 2
[Ct`2] Cycle Time 2
[db`2] Dead Band 2
[A2hi] Alarm 2 High
[A2Lo ] Alarm 2 Low
[A3hi] Alarm 3 High
[A3Lo] Alarm 3 Low
[A4hi] Alarm 4 High
[A4Lo] Alarm 4 Low
[P``t] Proportional Term
[I``t] Integral Term
[d``t] Derivative Term
[hYS1] Hysteresis 1
[hYS2] Hysteresis 2
[AhY2] Alarm Hysteresis 2
[AhY3] Alarm Hysteresis 3
[AhY4] Alarm Hysteresis 4
[SP`1] Set Point 1
¿
¯
Figure 5.1 – Parameters available for the Custom Menu
(*default selections).
Note: The Custom Menu will not appear if the ramping
software option has been ordered (96XX-XXXX-AAXX).