Watlow Series 96 - Manual (Page 70)

Series 96 Software Map
[``96]
Process 1 Value
[``96]
[``96]
Custom Menu**…
[``P1]
Home Page
Set Point Value,
Remote Set Point Value
or Percent Output Value
Setup Page
[InP1]
Input 1 Menu
[`SEt] Setup Page
[SEn1] Sensor Type _______________
[In`1] Input Type 1 _______________
[rL`1] Range Low 1_______________
[rh`1] Range High 1 ______________
[dEC1] Decimal 1 _________________
[Ftr1] Input Software Filter 1 _______
[InP2]
Input 2 Menu
[`SEt] Setup Page
[In`2] Input 2** __________________
[rL`2] Range Low 2** _____________
[rh`2] Range High 2** _____________
[CAL2] Calibration Offset 2**_________
[E`Fn] Event Function _____________
[E`cn] Event Condition ____________
[absp] Abort Set Point* ____________
[Out1]
Output 1 Menu
[`SEt] Setup Page
[Ot`1] Output 1 __________________
[Prc1] Process Type 1 _____________
[Out2]
Output 2 Menu
[`SEt] Setup Page
[Ot`2] Output 2 __________________
[Prc2] Process Type 2 _____________
[AtY2] Alarm Type 2_______________
[AhY2] Alarm Hysteresis 2 __________
[LAt2] Latching 2 _________________
[SIL2] Silencing 2 ________________
[Sid2] Alarm Active Sides 2 _________
[Lgc2] Alarm Logic 2 ______________
[Anu2] Alarm Annunciation 2 ________
[Out3]
Output 3 Menu
[`SEt] Setup Page
[Ot`3] Output 3 __________________
[AtY3] Alarm Type 3_______________
[Ahy3] Alarm Hysteresis 3 __________
[LAt3] Latching 3 _________________
[SIL3] Silencing 3 _________________
[Sid3] Alarm Active Sides 3 _________
[Lgc3] Alarm Logic 3 _______________
[Anu3] Alarm Annunciation 3 _________
[Out4]
Output 4 Menu
[`SEt] Setup Page
[Ot`4] Output 4 __________________
[AtY4] Alarm Type 4 _______________
[Ahy4] Alarm Hysteresis 4 __________
[LAt4] Latching 4 _________________
[SIL4] Silencing 4 _________________
[Sid4] Alarm Active Sides 4 _________
[Lgc4] Alarm Logic 4 _______________
[Anu4] Alarm Annunciation 4 _________
[Aout] Analog Output 4 _____________
[Prc4] Process Type 4 _____________
[A`hi] Analog Output High __________
[A`lo] Analog Output Low __________
[ACAL] Analog Output Offset _________
[BaUd] Baud Rate _________________
[Addr] Address ___________________
[gLbL]
Global Menu
[`SEt] Setup Page
[Unit] Units Type_________________
[`C-F] C or F ____________________
[`Err] Input Error Latching _________
[FAIL] Failure Mode**______________
[MAn] Manual Default Power** ______
[PLSP] Power Limit Set Point ________
[PL`A] High Power Limit Above ______
[PL`b] High Power Limit Below ______
[``rP] Ramping Mode**____________
[rP`S] Ramp Scale** ______________
[ratE] Ramp Rate**_______________
[OPLP] Open Loop Detect __________
[ptyP] Program Type* _____________
Operations Page
[Mon]
Monitor Menu
[OPEr] Operations Page
[Pr2`] Process 2** __________________
[Pcnt] Percent Output _______________
[rPSP] Ramping Set Point** ___________
[E`St] Event Input Status ____________
[USEr]
User Menu
[OPEr] Operations Page
[A-M] Auto-Manual Operations Mode** __
[`Aut] Auto-tune ___________________
[AtSP] Auto-tune Set Point____________
[`SP2] Set Point 2** _________________
[E`SP] Event Set Point**______________
[`L-r] Local or Remote Mode**________
[CAL1] Calibration Offset _____________
[PId1]
PID 1 Menu
[OPEr] Operations Page
[Pb`1] Propband 1 __________________
[It`1] Integral 1____________________
[rE`1] Reset 1 _____________________
[dE`1] Derivative 1__________________
[rA`1] Rate 1 ______________________
[brS1] Burst 1______________________
[Ct`1] Cycle Time 1 _________________
[hYS1] Hysteresis 1 _________________
[db`1] Dead Band 1 ________________
[PID2]
PID 2 Menu
[OPEr] Operations Page
[Pb`2] Propband 2 __________________
[It`2] Integral 2 ___________________
[rE`2] Reset 2 _____________________
[dE`2] Derivative 2 _________________
[rA`2] Rate 2 ______________________
[brS2] Burst 2 _____________________
[Ct`2] Cycle Time 2 ________________
[hYS2] Hysteresis 2 _________________
[db`2] Dead Band 2 ________________
[ALM]
Alarm Menu
[OPEr] Operations Page
[A2Lo] Alarm 2 Low _________________
[A2hi] Alarm 2 High _________________
[A3Lo] Alarm 3 Low _________________
[A3hi] Alarm 3 High _________________
[A4Lo] Alarm 4 Low _________________
[A4hi] Alarm 4 High _________________
Factory Page
[CUSt]
Custom Menu**
[FctY] Factory Page
[``P1] __________________________
[``P2] __________________________
[``P3] __________________________
[``P4] __________________________
[``P5] __________________________
[``P6] __________________________
[``P7] __________________________
[``P8] __________________________
[``P9] __________________________
[`P10] __________________________
[`P11] __________________________
[`P12] __________________________
[`P13] __________________________
[`P14] __________________________
[`P15] __________________________
[`P16] __________________________
[`LOC]
Lockout Menu
[FctY] Factory Page
[``SP] Set Point Lock ______________
[prog] Program Menu Lock* ________
[CuSt] Custom Menu Lock** ________
[OPEr] Operations Page Mode _______
[`SEt] Setup Page Lock ____________
[`CAL] Calibration Menu Lock ________
[dIAg]
Diagnostics Menu
[FctY] Factory Page _______________
[MdL] Model Number______________
[dAtE] Date of Manufacture _________
[`Sn1] Serial Number 1 ____________
[`Sn2] Serial Number 2 ____________
[Soft] Software ID Number _________
[ItY2] Input Type 2 ________________
[`rEu] Software Revision ___________
[OTY1] Output 1 Hardware __________
[Oty2] Output 2 Hardware __________
[Oty3] Output 3 Hardware __________
[Oty4] Output 4 Hardware___________
[tout] Test Output _________________
[dISP] Test Displays _______________
[hrES] High Resolution _____________
[AMb] Ambient Temperature ________
[Acnt] Ambient A-D Counts _________
[cnt1] Channel 1 A-D Counts _______
[cnt2] Channel 2 A-D Counts _______
[tSht] Communications Test/
Troubleshooting ____________
[LinE] Line Frequency _____________
Enter your settings on a photo-
copy of this page.
The Factory Page also includes
calibration parameters that are
not necessary for everyday use
of the controller. Calibration
parameters and procedures are
explained at Watlow’s web site,
http://www.watlow.com/litera-
ture/prodtechinfo. Search on 96
calibration manual.
*Menu added if ramping version
of the controller is selected
(96__-____-AA__).
**Menu removed if ramping
version of the controller is
selected (96__-____-AA__).
Program Menu
*
(see pg. 7.1)