Kenwood KDC-W9537U - Manual (Page 53)

English | 53
Some functions of this unit may be disabled by
some settings made on this unit.
! Cannot switch to Aux source.
▲ • AUX is not turned on. ☞ <Built-in Auxiliary input
Setting> (page 44)
• AUX cannot be used when the KCA-iP200 is
connected.
!
• Cannot set up the Fader.
• No Audio control effect on AUX.
▲ The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
! • Cannot set up the equalizer.
• Cannot set up WOW HD.
• Cannot set up the crossover network.
• Cannot set up Digital Time Alignment.
• Cannot preset the sound system.
▲ • The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
• In the speaker select option, None is selected for
the rear speakers. ☞ <Sound Management system>
(page 12)
! • Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
▲ • In the speaker select option, None is selected for
the related speakers. ☞ <Sound Management
system> (page 12)
• <Subwoofer Output> (page 10) is not set to On.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
! • Cannot set up the sound management system.
• Cannot set up the position.
▲ The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
!
Cannot set up SRS 3D Space Control or SRS 3D
Center Control.
▲ The tuner or DAB source is in use.
!
Cannot set up the SRS 3D Center Control.
▲ SRS 3D Space control is set to OFF. ☞ <WOW HD
Control> (page 14)
! Cannot set up the Dual zone function.
▲ In the speaker select option, None is selected for
the rear speakers. ☞ <Sound Management system>
(page 12)
! • Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
▲ The Dual zone function is disabled. ☞ <Audio
Setup> (page 9)
! • Cannot register a security code.
• Cannot set up Display Illumination Control.
▲ <Demonstration mode Setting> (page 46) is not
turned off.
!
Cannot play audio files.
▲ <CD Read Setting> (page 44) is set to "2".
! • Cannot File select.
• Cannot direct music search.
▲ The Random play function is enabled.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
? The Touch Sensor Tone does not sound.
✔ The preout jack is being used.
☞ The Touch Sensor Tone cannot be output from
the preout jack.
?
Switching between negative and positive display
modes takes place automatically.
✔ Switching between negative and positive display
modes takes place automatically to maintain the
initial brightness of the display for a long period of
time.
☞ You can select "Display N/P: POSI" as mentioned
in <Display-reversing Setting> (page 40).
Tuner source
? Radio reception is poor.
✔ The car antenna is not extended.
☞ Pull the antenna out all the way.
✔ The antenna control wire is not connected.
☞ Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
Troubleshooting Guide
B64-3773-00_00_E_English.indd 53 B64-3773-00_00_E_English.indd 53 07.5.10 5:18:49 PM 07.5.10 5:18:49 PM