Kenwood KDC-W9537U - Manual (Page 54)

54 | English
Disc source
?
The specified disc does not play, but another one
plays instead.
✔ The specified CD is quite dirty.
☞ Clean the CD.
✔ The disc is loaded in a different slot from that
specified.
☞ Eject the disc magazine and check the number
for the specified disc.
✔ The disc is severely scratched.
☞ Try another disc instead.
? Cannot remove disc.
✔ Downloading picture.
☞ Eject is disabled while downloading picture.
Audio file source
?
The sound skips when an Audio file is being
played.
✔ The media is scratched or dirty.
☞ Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 7).
✔ The audio file is broken or not supported.
☞ Damaged and unsupported files are skipped.
✔ The recording condition is bad.
☞ Record the media again or use another media.
USB device source
? The USB device is not detected.
✔ The USB connector is disconnected.
☞ Connect the connector of the USB device
properly.
?
The USB device does not play its audio files.
✔ The USB connector is disconnected.
☞ Connect the connector of the USB device
properly.
? Cannot USB remove mode.
✔ Downloading picture.
☞ USB remove mode is disabled while
downloading picture.
The messages shown below display your
systems condition.
Eject: • No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
• No CD in the unit.
No Disc: No disc has been loaded in the disc
magazine.
TOC Error: • No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
Read Error: • The number of files or folders which are
stored in the connected USB device is above
the limitation.
• The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again referring to http://www.
kenwood.com/usb/. If the error message is
still displayed, initialize the USB device or
use other USB devices.
Error 05: The disc is unreadable.
Blank Disc: Nothing has been recorded on the MD.
No Track: No tracks are recorded on the MD, although it
has a title.
No Panel: The faceplate of the slave unit being
connected to this unit has been removed.
Error 77: The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"Error 77" code does not disappear, consult
your nearest service center.
Mecha Error: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the "Mecha
Error" code does not disappear, consult
your nearest service center.
Hold Error: The protective circuit in the unit activates
when the temperature inside the automatic
disc changer exceeds 60°C (140°F), stopping
all operation.
➪ Cool down the unit by opening the
windows or turning on the air conditioner.
As the temperature falls below 60°C
(140°F), the disc will start playing again.
No Name: Attempted to display DNPS during the CD
play having no disc names preset.
Waiting: Radio text data is being received. Radio text
plus requires more time to load than radio
text.
Load: Discs are being exchanged in the Disc
changer.
Checking:
Reading:
The unit is reading the data on the disc, USB
device or Internal Memory.
IN (Blink): The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
Troubleshooting Guide
B64-3773-00_00_E_English.indd 54 B64-3773-00_00_E_English.indd 54 07.5.10 5:18:50 PM 07.5.10 5:18:50 PM