Dell PowerVault 50F (Fibre Channel Switch) User Manual
Page 89
Error Messages: Dell™ PowerVault™ 50F 8-Port Fibre Channel Switch Installation and Troubleshooting Guide
file:///C|/Users/sharon_anand/Desktop/PowerVault/50f_enit/ERROR.HTM[3/15/2013 11:32:10 AM]
SCN (3)
The path selection task has
received a State Change
Notification message that it does
not recognize.
Check that all paths and routing tables are correct. If they are not,
reboot the local switch.
VERSION (2)
The FSPF protocol version running
on the local switch is lower than a
neighbor's switch.
Check the protocol version on both switches using the fspfShow
command. If the two versions differ, update the software on the
local switch.
HLO
INVHLO (1)
The path selection task has
received a HELLO message with
an invalid parameters from a
neighbor switch.
Check that all paths and routing tables are correct. If they are not,
reboot the neighbor switch.
Check the paths and routes again. If they are still incorrect,
reboot the local switch.
LSDB
LSID (2)
A Link State Record received as
part of a Link State Update has an
out of range domain ID.
Check that all paths are correct. If any path is missing to any
switch in any part of the fabric, reboot the switch with the missing
path.
MCAST ADDBRANCH
(2)
A branch is being added to a
broadcast or multicast tree, but the
parameters are incorrect.
If this is caused by a configuration command, check the
parameter values. Otherwise, check the broadcast tree with the
bcastShow command. If the tree is incorrect, reboot the local
switch.
ADDPORT (3)
A multicast routing table
programming failed.
Run the portLogShow command. Contact Customer Support.
NOPARENT (2) An error occurred while computing
a broadcast or multicast tree.
Run the LSDbAllShow command. Contact Customer Support.
NOPARENTLSR
(2)
An error occurred while computing
a broadcast or multicast tree.
Run the LSDbAllShow command. Contact Customer Support.
REMPORT (3)
Removing an entry from a multicast
routing table failed.
Run the portLogShow command. Contact Customer Support.
SPFCOST (3)
An error occurred with computing
the multicast path tree.
Run the LSDbAllShow command. Contact Customer Support.
NBFSM NGBRSTATE
(2)
An error occurred in the neighbor
Finite State
Check the neighbor's state with the nbrStateShow command.
If the state is not NB_ST_FULL, force a state change with the
portDisable command followed by portEnable.
After a few seconds, if the state is not NB_ST_FULL, reboot both
the local and remote switches.
UCAST ADDPATH (1)
A static path configuration failed.
Check command parameters.
RELICPDB (2)
The path selection task received an
E_Port SCN, but the port was
already ISL.
Run the ucastAllShow command. Contact customer support.
SPFCOST(3)
An error occurred with computing
the unicast path tree.
Run the LSDAllShow command. Contact customer support.
MQ
QREAD (1)
A task was unable to receive a
message.
Run the command show <queue ID> with the ID of the queue
reported in the error. Contact customer support.
QWRITE (1)
A task was not able to post a
message on a queue.
See "
" for more information.
SYS
NOMEM (1)
The system's memory is
exhausted.
Reboot the switch. Contact customer support.
SYSCALL (2)
A system call into VxWorks failed.
Reboot the switch. Contact customer support.
TIMERS ENQFAIL (1)
An error occurred while setting a
timer.
Reboot the switch. Run the commands actTimersShow and
timerShow <timer ID>. Contact customer support.
MSG (3)
The timer task received an
unknown message.
Contact customer support.
Panic Errors