SINGER XL-580 - Manual (Page 96)

94
Fig. 1
Fig. 1
Fig. 1
Multi-Hoop
Multi-hooping is a special feature in the software that will allow
embroidery data which is larger than a single embroidery hoop
to be sent to the machine to stitch out, while making it easy to
rehoop the fabric so that each part of the design lines up exactly.
This embroidery data may be a single design that is too large for
the hoop or a combination of smaller embroidery elements and/
or lettering, that when combined together make a much larger
¿QLVKHGGHVLJQ6HH)LJ
The Multi-Hoop feature splits the design elements in up to four
different parts; and then sews them precisely, matching one
section to the other. When re-hooping the fabric, the Multi-
hoop feature will compensate for misalignment if the fabric has
been placed slightly askew in the hoop.
When stitching an embroidery design that is too large for the
KRRSLWFDQEHGLI¿FXOWWRUHKRRSWKHIDEULFZLWKH[DFWDOLJQPHQW
Multi-Hoop utilizes a system where three alignment points (A, B,
and C) are input on cross lines that have been marked onto the
fabric. When these points are input, they inform the machine
exactly as to how the fabric is positioned into the hoop and will
therefore sew the design to the alignment of the cross lines. If
the fabric is slightly askew, this system will compensate for it and
sew accordingly. Please note: the Multi-Hoop feature will only
compensate for a slight misalignment in the vertical cross line.
Please try to hoop the fabric as accurately as possible.
Preparing the Fabric
Please note: The fabric must be large enough to
accommodate the amount of hoops that will be required to
stitch out the design.
1. Using a very¿QHOLQHGZDWHUVROXEOHPDUNHUPDUNDOLQH
vertically down the center of the fabric.
2. Mark a line horizontally across the center of the fabric.
The vertical and horizontal lines must be at precise right
angles to each other. These lines will now be referred to
as the”cross lines”. These cross lines will be used to set
the fabric into the hoop according to the divided design
layout.
In the Software
1. Select
Tools from the horizontal tool bar, select Hoop
and then select Multiple.
2. A single hoop appears on the screen marked with #1 in
the upper left corner.
Cross line
Ligne de
marquage.
Línea de
cruce
Intersection of cross
lines must be at perfect
90 degree angles.
L'intersection de lignes
de marquage doit être
à un angle parfait de 90
degré.
Intersección de las
líneas de cruce deben
e s t a r e n á n g u l o s
perfectos de 90 grados
Fabric
Tissus
Tela
Fig. 2
Fig. 2
Fig. 2
Please Note: a thin line is very important to the
DFFXUDF\RIWKH¿QDORXWFRPHRIWKHHPEURLGHU\
Notez s'il vous plaît : Une ligne mince est très importante
SRXUO
H[DFWLWXGHGXUpVXOWDW¿QDOGHODEURGHULH
Por favor Note: una línea delgada es muy importante
SDUDODSUHFLVLyQGHOUHVXOWDGR¿QDOGHODERUGDGRUD
Please note: Up to three
additional hoops will
appear as the design
data requires.
Notez s'il vous plaît :
Jusqu'à trois cerceaux
s u p p l é m e n t a i r e s
apparaîtront selon les
exigences du dessin de
broderie.
Por favor Note: Aparecerán
hasta tres aros adicionales
si así lo requieren los
datos de diseño.
L O V E
Cross line
Ligne de
marquage
Línea de
cruce