KEYENCE GT2-500 Series - Manual (Page 2)

2 GT2-500-M-E
Package Contents
The product package of each model should include the following items.
Check that all items are included before use.
■ Amplifier parts
● Amplifier
■ Sensor head parts
● Sensor head
● Sensor head connection cable
We have taken all possible precautions in packaging; however, if
any parts are found to be defective or broken, please contact your
nearest KEYENCE sales office.
Mounting the Amplifier and Wiring
■ Mounting the amplifier
● GT2-500 (Main unit)
1
Fit the tab of the lower part of the main unit to
the DIN rail. While inserting the main unit in
the direction of Arrow (1), push the body down
in the direction of Arrow (2).
2
To detach the amplifier, while pushing the main unit in the direction of
Arrow (1), pull the body up in the direction of Arrow (3).
● GT2-550 (Expansion unit)
The expansion unit can only be used in addition to the main unit.
Up to 2 expansion units can be added to one main unit.
1
Mount the expansion unit to be added to the DIN rail.
2
Push and fix the expansion unit to the connector of the main unit until it clicks.
3
Mount the end units (OP-26751: a set of two pieces) sold separately on
both sides of the amplifiers (the main unit and the expansion unit),
then fix the end units with screws on the upper part of each end unit (2
points x 2 units).
The mounting method of the end unit is the same as that of the amplifier.
■ Connecting to DL Series Communication Units
For details on communication methods, see the DL Series manuals.
1
Attach the DL Series to the DIN rail and connect it to the amplifier.
2
Attach 1 end unit (OP-26751: 2 units) to the side of the amplifier, and 1
to the side of the DL Series Communication Unit. Attach using the
screws on top of the end units (2 screws on each unit).
NOTICE
• The M8 L-shaped connector type cable cannot be
used with the GT2-H32(L)/H50/A32/A50.
• When a protection rating of IP67G and NEMA Type
13 enclosure is required for GT2-P12K(F)/P12(F),
or a protection rating of IP67G is required for GT2-
PA12K/GT2-PA12 use an M8 oil-resistant straight
connector type cable. Other cables do not meet the
IP67G protection rating or NEMA Type 13
enclosure rating.
GT2-500 (Main unit) GT2-550 (Expansion unit)
Amplifier x 1 Amplifier x 1 Instruction manual x 1
GT2-H12K/H12 GT2-H12KL/H12L
Sensor head x 1 Sensor head x 1
Precautions for Handling x 1 Precautions for Handling x 1
GT2-A12KL/A12L
Sensor head x 1
Precautions for handling x 1
GT2-H32 GT2-H32L
Sensor head x 1 Sensor head x 1
Precautions for Handling x 1 Precautions for Handling x 1
GT2-A12K/A12
Sensor head x 1
Precautions for handling x 1
Sensor head x 1 Sensor head x 1
Precautions for handling x 1 Precautions for handling x 1
Sensor head x 1
Precautions for handling x 1 Sensor head x 1
Precautions for handling x 1
Nut x 1
Key spanner x 1
Sensor head x 1
Precautions for handling x 1
Nut x 1
Key spanner x 1 Sensor head x 1
Precautions for handling x 1
Nut x 1
Key spanner x 1
GT2-A32
Sensor head x 1
Precautions for Handling x 1
GT2-H50
Sensor head x 1
Precautions for Handling x 1
GT2-A50
Sensor head x 1
Precautions for Handling x 1
GT2-P12K/P12 GT2-P12KL/P12L GT2-PA12K/PA12
GT2-H12KF/H12F GT2-H12KLF/H12LF
GT2-P12KF/P12F
GT2-CH2M/5M/10M/20M
(M8 straight connector) GT2-CHL2M/5M/10M/20M
(M8 L-shaped connector) GT2-CHP2M/5M/10M
(M8 oil-resistant straight connector)
NOTICE
• When adding an amplifier (expansion unit), be sure
the power of both main and expansion units is OFF
before operation. Mounting when the power is ON
may damage the equipment.
• Be sure to completely connect an expansion unit to
a main unit. Oblique or improper connections may
damage the equipment.
NOTICE
Refer to the illustration on
the right to check that the
sensor amplifier
connection connector (for
attaching to DIN rails) on
the side of the DL Series
Communication Unit is
not bent. Connecting to
the sensor amplifier with a bent connector can lead to
equipment damage.
(1)
(2)
(3)
End unit
End unit
Amplifier
Connector
DL Series Communication Unit
Amplifier connection connector
DL Series Communication Unit
End unit
End unit