FingerTec k-Kadex - Manual (Page 2)

Installation
Note: Please read the instructions carefully before installing the k-Kadex.
The k-Kadex has one wire attached to it. For a neat installation, you need to conceal this wire
properly.
Remove the back piece of the k-Kadex from the main piece.
Secure the back piece of the k-Kadex onto or inside a wall using the 4 screws provided but
make sure that you have some space for the wire to go through the center hole. Plug the
main piece of the k-Kadex securely in place.
1
2
1
2
1
2
3
Note: There are 2
small hooks inside
the back piece.
Make sure this
portion is facing up.
Verification • Card
Wave a card at the card induction area to scan
the card. The k-Kadex captures the card informa-
tion and transmits it to the master terminal for
verification. Make sure that the k-Kadex is in its
standby mode, where the LED light is showing
red before you start using the terminal.
Make sure that you have enrolled the
user/card into the master terminal.
Wave the card at the card induction area. The
LED light will turn green and it will submit the
card information to the master terminal for
verification.
Verification result
a. Successful Verification: Green LED blinks
accompanied with a long beeping sound.
b. Failed Verification: Red LED blinks accom-
panied with two short beeping sound.
Verification • User ID & Password
Make sure that the k-Kadex is in its standby
mode, where the Red LED light is lit on and
the user ID and/or password(s) have been
enrolled into a master terminal before you
proceed with verification.
Insert a user ID, for example 1234. Ignore the
prefix zeros if the user ID has them. Press OK
to confirm the user ID You will hear a beep.
This is an indication that the User ID has
been sent to the master terminal.
Insert a password, for example 387034, and
press OK to confirm. If the password is
correct, you will hear a “beep” after you
press the OK button.
Verification result
a. Successful Verification: Green LED
blinks accompanied with a long beeping
sound.
b. Failed Verification: Red LED blinks
accompanied with two short beeping
sound.
Master terminal indication during the
verification process at the k-Kadex:
• Input a
username
• Input a
password
• During
successful
verification
• During
dailed
verification
Master terminal indication during
verification process at the k-Kadex:
• During
successful
verification
• During failed
verification
1
2
3
A Firm Access
with FingerTec
k-Kadex
SPECIFICATIONS
MODEL
SURFACE FINISHING
TYPE OF SCANNER
MICROPROCESSOR
MEMORY
ALGORITHM
PRODUCT DIMENSION (L X W X H), mm
STORAGE
• Cards
• Transaction
ENROLLMENT & VERIFICATION
• Methods
• Card per user ID
• Reading distance, mm
• Verification time (sec)
CARD TECHNOLOGY
• RFID: 64-bit, 125kHz
• MIFARE: MFIS50/S70, 13.56MHz
COMMUNICATIONS
• Method
OPERATING ENVIRONMENT
• Temperature (°C)
• Humidity (%)
• Power input
ACCESS CONTROL
• EM lock driving output
• Alarm output
• Antipassback
k-Kadex
Acrylonitrile Butadiene Styrene (ABS)
RFID antenna
Managed by master
75 x 20 x 115
Storage in master
Card or password
Managed by master
40 ~ 80 (RFID), 30 ~ 50 (Mifare)
Managed by master
Yes
Made to order
Wiegand 26-bit output
-10 ~ 70
20 ~ 80
DC 12V 1A
Managed by master
Pwd Affirm
User ID 00004
ESC OK
Pwd Affirm
User ID 00004
Input Pwd *_ __
Pwd Affirm
User ID 00004
Verified, TQ
Pwd Affirm
Error Pwd.
Verify
CARD: 0003837885
USER ID: 00001
VERIFIED
Verify PIN Card
No enroll
3
4
5
Card Password