4 cable and adaptor information, 5 hardware specifications, 1 signal descriptions – Analog Way ASCENDER 16 (LIVECORE) - Ref. ASC1602 User Manual User Manual

Page 14

Advertising
background image

14

4.4 Cable and adaptor information

A large choice of cables and adaptors are compatible with the LiveCore™ unit. Please refer to the hardware

specifications chapter to find the most suitable cables for your operations.

For each type of signal, here are the levels and the impedance accepted by the LiveCore™ unit.

4.4 Cable and adaptor information

4.5 Hardware specifications

4.5.1 Signal descriptions

Type

Levels

Impedance

Composite

0,7 Vpp + 0,3 Vpp

75 Ω

S. Video

Y = 0,7 Vpp + 0,3 Vpp

C = 0,7 Vpp

75 Ω

YUV

Y = 0,7 Vpp + 0,3 Vpp

U = 0,7 Vpp

V = 0,7 Vpp

75 Ω

RGsB

R = 0,7 Vpp

G = 0,7 Vpp + 0,3 Vpp

B = 0,7 Vpp

75 Ω

RGBS

R, G, B = 0,7 Vpp

R, G, B = 75 Ω

S = 0,3 Vpp 75 Ω

or

S = TTL

Type

Levels

Impedance

YUV

Y = 0,7 Vpp + 0,3 Vpp

U = 0,7 Vpp

V = 0,7 Vpp

75 Ω

RGsB

R = 0,7 Vpp

G = 0,7 Vpp + 0,3 Vpp

B = 0,7 Vpp

75 Ω

RGBS

R, G, B = 0,7 Vpp

R, G, B = 75 Ω

S = 0,3 Vpp 75 Ω

or

S = TTL

Type

Characteristics

SD-SDI

YUV - 10 bits – 4.2.2 - 270 Mb/s

No payload ID management

Only A-level type

DVI

RGB ou YUV – 8 bits – 4.4.4 – 16/235 - TMDS

HDMI

RGB or YUV – 10 bits – 4.4.4 or 4.2.2

– 16/235 – TMDS

DisplayPort

RGB or YUV – 10 bits – 4.4.4 or 4.2.2

– 16/235 – Main Link

Type

Characteristics

DVI

RGB or YUV – 8 bits – 4.4.4 – 16/235 - TMDS

HDMI

RGB or YUV – 10 bits – 4.4.4 or 4.2.2

– 16/235 – TMDS

DisplayPort

RGB or YUV – 10 bits – 4.4.4 or 4.2.2

– 16/235 – Main Link

Analog SDTV

Analog EDTV

Digital SDTV

Digital EDTV

Dismantling front handles of the device could invalidate warranty on after-sales services of your

LiveCore™ unit. It is strongly advised to avoid using front handles as rests for your LiveCore™

unit, they are designed for manipulation purposes only.

If required, front handles of the device can be dismantled, but with caution. The original screws removed

must not be reintroduced to their location without handles in place. Substantial damages can occur,

including risk of electric shock from the main voltage. Only M4x12mm screws can be used. They are

supplied with the unit.

Advertising