Beisler 2112-4 - Manual (Page 87)

- D 87 -
Short Seam Automat 2112-4 Working Instructions Beisler Automated Sewing Equipment
D.3
Programming
D.3.4 List of inputs and outputs
Valve Output
number
Cylinder
number
Signal
output
Valve
type
Y01 01 Open / close clamp 01 X25 Pin02 5/2 way
Y02 02 Move clamp in / out sideways 02 X25 Pin03 5/2 way
Y03 03 Swing folder left / right 03 X25 Pin08 5/2 way
Y04 04 Rotate folder 04 X25 Pin09 5/2 way
Y05 05 Open / close folder clamp 05 X25 Pin10 5/2 way
Y06 06 Close / open sliding table 06 X25 Pin11 5/2 way
Y07 07 Hubtisch auf 07 X25 Pin12 5/2 way
Y08 08 Raise / lower stacker stamp 08 X25 Pin14 5/2 way
Y09 09 Open / close pocket bag clamp 09 X26 Pin26 5/2 way
Y10 10 Thread clamp forward / rearward 10 X26 Pin18 5/2 way
Y11 11 Blow thread in X26 Pin18 5/2 way
Y12 12 Right front trousers component cutter 12 X26 Pin22 5/2 way
Y13 13 Slash selvage cutter 13 X26 Pin23 5/2 way
Y14 14 Left front trousers component cutter 14 X26 Pin24 5/2 way
Y 15 15 Vacuum on/off 15 X25 Pin01 5/2 way
Y16 16 Slash selvage clamp open / close 16 X26 Pin30 5/2 way
Y27 27 Scissors side pocket 27 X27 Pin25 5/2 way
Y31 31 Thread cutter 31 X25 Pin05 3/2 way
Y33 33 Blowing at stacker transport paral. to Y 08 33 X25 Pin14 3/2 way
Y34 34 Folder up 34 X25 Pin06 3/2 way
Y35 35 Folder down 34 X25 Pin07 3/2 way
Y36 36 Thread tension blower 36 X25 Pin04 3/2 way
Y37 37 Stacker transport rear 37 X25 Pin15 3/2 way
Y38 38 Stacker transport front 38 X25 Pin16 3/2 way
Y45 45 Blowing at clamp paral. to Y01 45 X25 Pin02 3/2 way
Y46 46 Blowing slash selvage X26 Pin28 3/2 way
Y47 47 Blowing parts X26 Pin27 3/2 way
Y48 48 Move lift table 48 X25 Pin13 2/2 way
Switch Input
number
Switch type Signal
input
S01 01 Start switch Footswitch Make X24 Pin01
S02 02 Footswitch slash selvage clamp Footswitch Make X27 Pin18
S04 04 Clamp reference point Initiator NPN Break X24 Pin03
S07 07 Folder at right stop Initiator NPN Make X24 Pin05
S08 08 Folder at left stop Initiator NPN Make X24 Pin04
S09 09 Stacker transport neutral position Initiator NPN Make X24 Pin07
S10 10 Stacker transport stop position Initiator NPN Make X24 Pin08
S21 21 Photocell beginning / end of seam Photocell NPN X24 Pin13
S22 22 Photocell stack height Photocell NPN X24 Pin14
S23 23 Top thread monitor Probe X24 Pin15
S24 24 Bottom thread monitor (chain stitch) Probe X24 Pin16
S25 25 Spool rest thread monitor (lock stitch) Photocell NPN X27 Pin17
Inputs
Outputs
Y 25 25 Swivel right slash selvage clamp in/out 25 X26 Pin31 5/2 way