Comtech EF Data SDM-300L3 - Manual (Page 365)

SDM-300L3 Satellite Modem Revision 1
Remote Control Operation MN/SDM300L3.IOM
A–13
ASYNC
Receive
Overhead
Baud Rate Command:
Response:
Status:
Response: <add/ROBR_nnnnn'cr'
>add/ROBR_nnnnn'cr''lf']
<add/ROBR_'cr'
>add/ROBR_nnnnn'cr''lf']
Where: nnnnn = 110, 150, 300, 600, 1200, 2400,
4800, 9600, 19200, or 38400.
Note: RX ASYNC Overhead only.
ASYNC
Transmit
Channel
Character
Length Command:
Response:
Status:
Response: <add/TCCL_n'cr'
>add/TCCL_n'cr''lf']
<add/TCCL_'cr'
>add/TCCL_n'cr''lf']
Where: n = 5, 6, 7, or 8 (characters).
Note: TX ASYNC Overhead only.
ASYNC
Receive
Channel
Character
Length Command:
Response:
Status:
Response: <add/RCCL_n'cr'
>add/RCCL_n'cr''lf']
<add/RCCL_'cr'
>add/RCCL_n'cr''lf'] Where: n = 5, 6, 7, or 8 (characters).
Note: RX ASYNC Overhead only.
ASYNC
Transmit
Channel
Stop Bits Command:
Response:
Status:
Response: <add/TCSB_n'cr'
>add/TCSB_n'cr''lf']
<add/TCSB_'cr'
>add/TCSB_n'cr''lf'] Where: n = 1 or 2 (stop bits).
Note: TX ASYNC Overhead only.
ASYNC
Receive
Channel
Stop Bits Command:
Response:
Status:
Response: <add/RCSB_n'cr'
>add/RCSB_n'cr''lf']
<add/RCSB_'cr'
>add/RCSB_n'cr''lf'] Where: n = 1 or 2 (stop bits).
Note: RX ASYNC Overhead only.
ASYNC
Transmit
Overhead
Channel
Parity Command:
Response:
Status:
Response: <add/TOCP_xxxx'cr'
>add/TOCP_xxxx'cr''lf']
<add/TOCP_'cr'
>add/TOCP_xxxx'cr''lf'] Where: xxxx = ODD, EVEN, or NONE.
Note: TX ASYNC Overhead only.
ASYNC
Receive
Overhead
Channel
Parity Command:
Response:
Status:
Response: <add/ROCP_xxxx'cr'
>add/ROCP_xxxx'cr''lf']
<add/ROCP_'cr'
>add/ROCP_xxxx'cr''lf'] Where: xxxx = ODD, EVEN, or NONE.
Note: RX ASYNC Overhead only.
ASYNC
Transmit
Communica
tions Type Command:
Response:
Status:
Response: <add/TCT_xxxxxxxx'cr'
>add/TCT_xxxxxxxx'cr''lf']
<add/TCT_'cr'
>add/TCT_xxxxxxxx'cr''lf'] Where: xxxxxxxx = RS232, RS485 (4- Wire),
RS485_2W (2-Wire).
Note: TX ASYNC Overhead only.
ASYNC
Receive
Communica
tions Type Command:
Response:
Status:
Response: <add/RCT_xxxxx'cr'
>add/RCT_xxxxx'cr''lf']
<add/RCT_'cr'
>add/RCT_xxxxx'cr''lf'] Where: xxxxx = RS232 or RS485.
Note: RX ASYNC Overhead only.
Transmit
Data Phase Command:
Response:
Status:
Response: <add/TDP_xxxx'cr'
>add/TDP_xxxx'cr''lf']
<add/TDP_'cr'
>add/TDP_xxxx'cr''lf'] Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
Receive
Data Phase
Command:
Response:
Status:
Response: <add/RDP_xxxx'cr'
>add/RDP_xxxx'cr''lf']
<add/RDP_'cr'
>add/RDP_xxxx'cr''lf']
Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
CTS Delay
Time Command:
Response:
Status:
Response: <add/CTSD_xx'cr'
>add/CTSD_xx'cr''lf']
<add/CTSD_'cr'
>add/CTSD_xx'cr''lf'] Where: xx = 0 to 60 (number of seconds).
IDR
Transmit
ESC Type Command:
Response:
Status:
Response: <add/IDRT_xxxxx'cr'
>add/IDRT_xxxxx'cr''lf']
<add/IDRT_'cr'
>add/IDRT_xxxxx'cr''lf'] Where: xxxxx = DATA (64K DATA) or AUDIO
(2x32K AUDIO).
Note: TX IDR Overhead only.
IDR
Receive
ESC Type Command:
Response:
Status:
Response: <add/IDRR_xxxxx'cr'
>add/IDRR_xxxxx'cr''lf']
<add/IDRR_'cr'
>add/IDRR_xxxxx'cr''lf'] Where: xxxxx = DATA (64K DATA) or AUDIO
(2x32K AUDIO).
Note: RX IDR Overhead only.
IBS
Transmit
ESC Type Command:
Response:
Status:
Response: <add/IBST_xxxxx'cr'
>add/IBST_xxxxx'cr''lf']
<add/IBST_'cr'
>add/IBST_xxxxx'cr''lf'] Where: xxxxx = DATA (64K DATA) or AUDIO
(2x32K AUDIO).
Note: TX IBS Overhead only.