Ivoclar Vivadent Monobond Etch & Prime - Manual

English
Description
Monobond Etch & Prime is used to condition silica-based ceramic surfaces
for the adhesive bond with luting composites from the Variolink or Multilink
product lines, for example.
Monobond Etch & Prime etches and silanizes silicate ceramic surfaces in one
working step.
Composition
Alcoholic aqueous solution of ammonium polyfluoride, silane methacrylate,
phosphoric acid methacrylate and colourant.
Indication
– Conditioning of silica-based ceramic surfaces for the adhesive bond with
luting composites
Contraindication
– Any use not listed in the indication
– If a patient is known to be allergic to any of the ingredients of Monobond
Etch & Prime.
– Intraoral application
Side effects
Systemic side effects are not known to date. In rare cases, components of
Monobond Etch & Prime may lead to sensitization. The product should no
longer be used in such cases.
Interactions
The contamination of surfaces conditioned with Monobond Etch & Prime with
saliva and blood must be prevented.
Usage
Conditioning of pretreated and non-pretreated restorations
made of silicate ceramic
(e.g. IPS Empress
® , IPS e.max ® Press, IPS e.max CAD)
– Following the try-in, thoroughly rinse the restoration with water spray and
dry with water- and oil-free air.
– Apply Monobond Etch & Prime on the adhesive surface using a
microbrush and agitate it into the surface for 20 seconds. Allow to react
for another 40 seconds.
– Then thoroughly rinse off Monobond Etch & Prime with water and dry
the restoration with a strong jet of water- and oil-free air for approximately
10 seconds.
Seat the conditioned restoration using a luting composite (e.g. Variolink ®
Esthetic or Multilink ® Automix) in accordance with the respective Instructions
for Use.
Additional notes
– To avoid any contamination, Monobond Etch & Prime must not be
removed directly from the bottle using a microbrush.
– Carefully close the Monobond Etch & Prime bottle immediately after use.
Warnings
– The product contains alcohols. Keep away from sources of ignition.
– Monobond Etch & Prime is corrosive. Avoid contact with the skin and
mucous membrane.
If the material should accidentally come in contact with the skin,
immediately wash with copious amounts of water.
– In rare cases, contact with the skin may lead to sensitization towards the
ingredients.
– Commercial medical gloves do not provide protection against the
sensitizing effect of methacrylates.
Storage
– Do not use Monobond Etch & Prime after the indicated date of expiration.
– Storage temperature 2–28°C (36–82°F)
– Shelf life: see expiry date on label
Keep out of the reach of children!
For use in dentistry only.
The material has been developed solely for use in dentistry. Processing should be carried
out strictly according to the Instructions for Use. Liability cannot be accepted for damages
resulting from failure to observe the Instructions or the stipulated area of application. The
user is responsible for testing the products for their suitability and use for any purpose not
explicitly stated in the Instructions. Descriptions and data constitute no warranty of attributes
and are not binding.
Deutsch
Beschreibung
Monobond Etch & Prime dient der Vorbereitung silikatischer
Keramikoberflächen für den adhäsiven Verbund mit Befestigungscomposites,
z.B. der Variolink- und Multilink-Produktlinie.
Monobond Etch & Prime ätzt und silanisiert silikatkeramische Oberflächen in
einem Arbeitsgang.
Zusammensetzung
Alkoholisch-wässrige Lösung von Ammoniumpolyfluorid, Silanmethacrylat,
Phosphorsäuremethacrylat und Farbstoff.
Indikation
– Vorbereitung von silikatischen Keramikoberflächen für den adhäsiven
Verbund mit Befestigungscompositen
Kontraindikation
– Anwendungen ausserhalb der Indikation.
– Bei erwiesener Allergie gegen Bestandteile von Monobond Etch & Prime.
– Intraorale Applikation.
Nebenwirkungen
Systemische Nebenwirkungen sind nicht bekannt. In seltenen Fällen können
Bestandteile von Monobond Etch & Prime zu einer Sensibilisierung führen.
In diesen Fällen ist auf die weitere Verwendung zu verzichten.
Wechselwirkungen
Eine Kontamination mit Monobond Etch & Prime behandelter Oberflächen
mit Speichel und Blut ist zu vermeiden.