Marantz NR1603 - Manual (Page 108)

105
Audio Delay
Default settings are underlined.
While viewing video, manually adjust the time to delay audio output.
Setting details
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” ( vpage 109 ) is set to
“On” and when a TV compatible with Auto Lip Sync is connected.
• Store “Audio Delay” for each input source.
• Audio Delay for game mode can be set when “Video Mode” (
vpage 110 ) is set to “Auto” or
“Game”.
Volume
Default settings are underlined.
Set the MAIN ZONE (room where the unit is located) volume setting.
Setting items Setting details
Scale
Set how volume is
displayed. 0 – 98 : Display in the range 0 (Min) to 98.
–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
• The “Scale” setting is applied also to the “Limit” and “Power On Level”
display method.
• The “Scale” setting applies to all zones.
Limit
Make a setting for
maximum volume. Off : Do not set a maximum volume.
60 (–20dB) / 70 (–10dB) / 80 (0dB)
Power On Level
Define the volume setting
that is active when the
power is turned on. Last : Use the memorized setting from the last session.
Mute : Always use the muting on condition when power is turned on.
1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
Mute Level
Set the amount of
attenuation when muting
is on. Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
Audio
Subwoofer Level
Default settings are underlined.
Sets the subwoofer on/off and its output level.
Setting items Setting details
Subwoofer
Turn subwoofer output on
and off. On : The subwoofer is used.
Off : The subwoofer is not used.
NOTE
This can be set when the sound mode is “DIRECT” or “PURE DIRECT”
(
vpage 68 ) and the “Subwoofer Mode” ( vpage 119 ) is
“LFE+Main”.
Subwoofer Level
Set the subwoofer output
level. –12dB – +12dB (0dB)
M-DAX
Default settings are underlined.
Compressed audio formats such as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the
amount of data by eliminating signal components that are hard for the human ear to hear. The M-DAX
function generates the signals eliminated upon compression, restoring the sound to conditions near those
of the original sound before compression. It also corrects the sense of volume of the bass to obtain richer
sound with compressed audio signals.
Setting items Setting details
Mode
Set the mode for M-DAX. Off : Do not use M-DAX.
Low : Optimized mode for compressed sources with normal highs.
Middle : Apply suitable bass and treble boost for all compressed sources.
High : Optimized mode for compressed sources with very weak highs.
• This item can be set with analog signals or PCM signal (Sample rate =
44.1/48 kHz) is input.
• “M-DAX” settings are stored for each input source.
• When set to “Off”, the M-DAX indicator on the front panel switches off.
• This cannot be set when the surround mode is set to “DIRECT” or
“PURE DIRECT”.
• This can also be set by pressing M-DAX .
Each time M-DAX is pressed, the setting is changed as shown below.
Off Low
Mid High
Basic v
ersion
A
dv
anced v
ersion
Inf
or
mations
A
dv
anced v
ersion
DVD