Marantz SR4001 User Manual
Page 30
27
ENGLISH
2-2 SPEAKERS DISTANCE
Use this parameter to specify the distance of each
speaker’s position from the listening position. The
delay time is automatically calculated according to
these distances.
Begin by determining the ideal or most commonly
used seating position in the room.
This is important for the timing of the acoustics to
create the proper sound space that the SR4001/
SR5001 and today’s sound systems are able to
produce.
Note:
For speakers that you have selected “NONE” the
Speaker Configuration sub-menu will not appear
here. (There are several useful books and special
DVD and LD’s available to guide you through proper
home theater confi guration. If you are unsure, have
your Marantz dealer perform the installation for you.
They are trained professionals familiar with even
the most sophisticated custom installations. Marantz
recommends the WWW.CEDIA.ORG website for
further information about this).
2-2 SPEAKERS DISTANCE
FRONT L : 10 ft 3.0 m
FRONT R : 10 ft 3.0 m
CENTER : 10 ft 3.0 m
SURR.L : 10 ft 3.0 m
SURR.R : 10 ft 3.0 m
SUB W : 10 ft 3.0 m
SURR.B L : 10 ft 3.0 m
SURR.B R : 10 ft 3.0 m
MAIN RETURN EXIT
1.
To select each speaker , press the
3
or
4
cursor buttons.
2.
To set the distance for each speaker , press the
1
or
2
cursor buttons.
3.
After you complete this portion of the set up,
move the cursor to “
NEXT
” with the
3
or
4
cursor buttons and then press the
ENTER
button to go to the next page.
FRONT L:
Set the distance from the front left speaker to your
normal listening position.
CENTER:
Set the distance from the center speaker to your
normal listening position.
FRONT R:
Set the distance from the front right speaker to
your normal listening position.
SURR. L:
Set the distance from the surround left speaker to
your normal listening position.
SURR. R:
Set the distance from the surround right speaker
to your normal listening position.
SUB W:
Set the distance from the subwoofer to your
normal listening position.
SURR. B L:
Set the distance from the surround back left
speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right
speaker to your normal listening position.
Notes:
• Set the distance to each speaker in meters (m) or feet
(ft) as follows.
m: 0.3 - 9 m in 0.3 m steps
ft: 1 - 30 ft in 1 ft steps
• For the speakers that you have selected “NONE” the
Speaker Size menu will not appear.
• The setting for Surr.Back L and Surr.Back R appears
if you set for it to, two surround back speakers in the
Speaker Size menu.
• The setting of Surr.Back appears if it is set for one
surround back speaker in the Speaker Size menu.
2-3. SPEAKERS LEVEL SETTING WITH TEST TONE
Here you will set the volume for each speaker so that
they are all heard by the listener at the same level.
We recommend using a SPL (Sound Pressure Level)
meter, when available.
Note:
The speaker level settings are not available in 7.1
Channel Input mode, CS mode and Multi Channel
Stereo mode.
2-3 SPEAKERS LEVEL
TEST MODE : MANUAL
FRONT L : 0 dB
CENTER : 0 dB
FRONT R : 0 dB
SURR.R : 0 dB
SURR.B R : 0 dB
SURR.B L : 0 dB
SURR.L : 0 dB
SUB W : 0 dB
MAIN RETURN EXIT
TEST MODE :
Selects “
MANUAL
” or “
AUTO
” for generating
the mode of the test tone with the
1
or
2
cursor
buttons.
If you select “
AUTO
” , the test tone will be cycled
through in a circular pattern which is Left
→
Center
→
Right
→
Surround Right
→
Surround Back Right
→
Surround Back Left
→
Surround Left
→
Subwoofer
→
Left
→
.. increments of 2 seconds
for each channel.
Using the
1
or
2
cursor buttons, adjust the volume
level of the noise from the speaker so that it is the
same level for all the speakers.
If you select “
MANUAL
”, adjust the output level of
each speaker as listed below.
1.
When you move the cursor to FRONT L by
pressing the
4
cursor button, the SR4001/
SR5001 will emit a pink noise from the front left
speaker.
Remember the level of this noise and then
press the
4
cursor button.
(Note that this can be adjusted to any level
between -10 and +10 dB in 1 dB intervals
except the subwoofer setting. The subwoofer
can be adjusted to any level between -15 and
+10 dB in 1 dB intervals.)
The SR4001/SR5001 will now emit the pink
noise from the center speaker.
2.
Using
the
1
and
2
cursor buttons, adjust the
volume level of the noise from the center
speaker so that it is the same level as the front
left speaker.
3.
Press
the
4
cursor button again. The SR4001/
SR5001 will now emit the pink noise from the
front right speaker.
4.
Repeat
steps
2
and
3
above for the front
right and other speakers until all speakers are
adjusted to the same volume level.
After you complete this portion of the set up, press
the
ENTER
button, the cursor will move to “
MAIN
”
and then press the
ENTER
button to go to SETUP
MAIN MENU.
Notes:
• Speakers that you selected “NONE” for in the
Speaker Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears
if you have set it for two surround back speakers in
the Speaker Size menu.
• The setting of Surr.Back appears if you have set it for
one surround back speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input
sources, you will need to use the 7.1CH-INPUT sub
menu. (See page 29).
3 PREFERENCE
3 PREFERENCE
STANDBY MODE : ECONOMY
TV-AUTO :
OSD INFO : ENABLE
BILINGUAL : MAIN
VIDEO CONVERT
HDMI : ENABLE
DC TRIGGER
MAIN
EXIT
1.
Select
“
PREFERENCE
” in the SETUP MAIN
MENU with the
3
or
4
cursor buttons, and
press the
ENTER
button.
2.
To select a desired content, press the
3
or
4
cursor buttons.
STANDBY MODE:
When this function is set to “
ECONOMY
”, you can
reduce the power consumption when the unit is in
the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the
“ECONOMY” setting (SR5001 only).
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with the
1
or
2
cursor buttons.
OSD Info:
Select the OSD information function to enable or
disable with the
1
or
2
cursor buttons.
If you select “
ENABLE
”, the SR4001/SR5001 will
display the status of the feature (Volume up/down,
input select, etc..) on the TV monitor. But if you do
not desire this information, select “
DISABLE
”.
BILINGUAL:
In the Bilingual mode, Dolby Digital and DTS
output is set to either “
MAIN
” or “
SUB
”. Select
“
BILINGUAL
” with the
1
and
2
cursor buttons,
then select
MAIN
↔
SUB
↔
MAIN+SUB
with the
1
or
2
cursor buttons.