Marantz SR4001 User Manual
Page 44
41
ENGLISH
LISTENING TO XM SATELLITE RADIO
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must
fi rst select the input source on the SR5001.
MULTI
SPEAKER
MULTI
PURE
SURROUND
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
MODE
1.
P.SCAN
T.MODE
+10
HT-EQ
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
BAND
CL
SOURCE
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
0
0
2.
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AMP
AUX2
VCR
DSS
TV
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
TUNER
TUNER
1.
MULTI
SPEAKER
DIGITAL
R
L
VIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
MULTI
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
2.
(Using the SR5001)
1.
Turn
the
INPUT SELECTOR
knob to select
“TUNER”.
2.
Press
the
BAND
button to select XM band.
(Using the remote control unit)
1.
To select tuner, Press the
TUNER
button twice
within two seconds on the remote.
2.
Press
the
BAND
button to select XM band.
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
-
F.DIRECT
PTY
TUNING
PRESET
-
+
+
ENTER
EXIT
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISP
T.DISP
1.
1.
Press
the
T.DISP
button 3 times to displayed
Signal Status.
S I G N A L :
• The display changes as shown below according to
the receiving condition.
SIGNAL:
■ ■ ■ ■ ■ ■
SIGNAL: STRONG
(Signal strength is good)
SIGNAL:
■ ■ ■ ■
SIGNAL: MARGINAL
(Signal strength is Marginal)
SIGNAL:
■ ■
SIGNAL: WEAK
(Signal strength is poor)
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
2.
Adjust the antenna location until signal strength
is good.
3.
Select channel 0 (XM000) with the
3
or
4
cursor buttons of the SR5001 or the
Q
or
R
buttons of the remote control unit.
MULTI
SPEAKER
SETUP
SIMPLE
MULTI
PURE
SURROUND
DISPLAY
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
ENTER
3.
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
+
+
REMOTE CONTROLLER
TAPE
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVD
VCR
DSS
TV
3.
• The Radio ID is displayed.
X M O O O R A D I O I D
Notes:
• If “ANTENNA” appears in the front panel display,
the XM Connect-and-Play antenna or Passport
system may not be connected to the XM terminal on
the rear panel of this unit properly.
• The ATT function is also effective when XM is
selected.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
-
F.DIRECT
PTY
TUNING
PRESET
-
+
+
ENTER
EXIT
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISP
T.DISP
1.
1.
Press the
T.DISP
button to displayed
INFORMATION.
Artist name/Song title
Channel category
Channel number/name
Signal Status
When the Channel number/name is displayed:
X M O 4 0 : D e e p T r c
4 0 : D e e p T r a c k s
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.