Marantz SR4001 - Manual (Page 31)

28
ENGLISH
6 CS II (CIRCLE SURROUND II) PARAMETER
6 CS II PARAMETER
TRUBASS : 0
SRS DIALOG : 0
MAIN EXIT
1. Select “ CS II ” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the
ENTER button.
2. To Select desired contents as below, press the
3 or 4 cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1
level interval with the
1 or 2 cursor buttons.
TRUBASS produced by the speakers are an octave
below the actual physical capabilities of the speakers
adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the
1 or 2 cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “
NONE ” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “
MAIN ” with the 3 or 4 cursor buttons and
press the ENTER button.
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable
or disable with the
1 or 2 cursor buttons. (Video
cable connection: Refer to page 19)
3-1 VIDEO CONVERT
TV : ON
DVD : ON
VCR1 : ON
DSS : ON
AUX1 : ON
MAIN RETURN EXIT
After you complete this portion of the set up, move
the cursor to “
MAIN ” with the 3 or 4 cursor buttons
and press the ENTER button.
HDMI AUDIO:
This setting determines whether to playback audio
input to the HDMI jacks through the SR4001/
SR5001 or output it through the receiver to a TV
or projector.
ENABLE: The audio input to the HDMI jacks
can be played back by this receiver.
In such case, audio signals are not
output to the TV or projector.
THROUGH: The audio input to the HDMI jacks is
not output from the speaker terminals
of the SR4001/SR5001. Audio data is
output directly to the TV or projector.
This setting is used to listen to audio
on a multi channel TV, etc.
DC TRIGGER:
Select “ DC TRIG SETUP ” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
3-2 DC TIRGGER SETUP
DC TRIG DISABLE
TV : CD :
DVD : TAPE :
VCR1 : CD-R :
DSS : AUX2 :
AUX1 : TUNER:
7.1CH:
MAIN RETURN EXIT
You can select MAIN ROOM, MULTI ROOM,
REMOTE or DISABLE by pressing
1 or 2 cursor
buttons.
Notes:
• REMOTE is available for the external control. The
RC5001SR cannot operate this function.
• To select desired input source , press 3 or 4 cursor
button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor
buttons and press the ENTER button.
4 SURROUND
4 SURROUND
SURR.MODE :AUTO
HT-EQ :OFF
LFE LEVEL :
MAIN EXIT
1. Select “ SURROUND ” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2. To select a desired content , press the 3 or 4
cursor buttons.
SURR.MODE:
Select the desired surround mode with the 1 or 2
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
fi lm soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the
1 or 2 cursor
buttons.
After you complete this portion of the set up, move
the cursor to “
MAIN ” with the 3 or 4 cursor buttons
and press the ENTER button.
5 PL II (PRO LOGIC II)
MUSIC PARAMETER
Pro Logic II -Music mode creates a rich and enveloping
surround ambience from stereo sources such as
CDs.
In this mode, SR4001/SR5001 includes three controls
to fi ne-tune the soundfi eld as follows.
5 PL II MUSIC PARAMETER
PARAMETER : DEFAULT
PANORAMAA : OFF
DIMENSION : 3
CENTER WIDTH : 3
MAIN EXIT
Select “ PL II MUSIC ” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the ENTER
button.
PARAMETER:
Select “ DEFAULT ” or “ CUSTOM ” with the 1 or 2
cursor buttons.
If you select “
CUSTOM ”, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
1 or 2 cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level
in 1 level intervals with the
1 or 2 cursor buttons.
Adjust the soundfi eld either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the
1 or 2 cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the center
is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If “
NONE ” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “
MAIN ” with the 3 or 4 cursor buttons and
press the ENTER button.