Marantz SR4001 - Manual (Page 39)

36
ENGLISH
OTHER FUNCTION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the SR4001/SR5001.
AUTO POWER ON
1. Be sure the TV auto mode is ENABLED. (Refer
page 27 : System Setup)
2. Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3. Turn OFF the power to the TV TUNER and the
SR4001/SR5001.
4. Turn ON the TV TUNER and tune in a receivable
station.
5. When the station is received, the SR4001/
SR5001 turns ON and TV is selected
automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2. The power to the SR4001/SR5001 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR4001/
SR5001 is set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
ATTENUATION TO ANALOG INPUT SIGNAL
-
T.DISP F.DIRECT PTY
TUNING PRESET - + +
MD CDR CD
DVD VCR
TUNER
DSS TV
BASS TREBLE
REC
AUDIO ANGLE DISC+
CH-SEL V-OFF
SUB TITLE SUB TITLE
ATT. ATT.
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“
PEAK ” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote.
“
ATT ” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT
and DSS/VCR2-OUT.
This function is memorized for each individual input
source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR4001/
SR5001’s output through a pair of headphones.
Be certain that the headphones have a standard
1/4” stereo phono plug. (Note that the speakers will
automatically be turned off when the headphone jack
is in use.)
MULTI SPEAKER SETUP SIMPLE MULTI PURE SURROUND
STANDBY
PHONES POWER ON/STANDBY
INPUT SELECTOR AV SURROUND RECEIVER SR5001
DIRECT
AUTO HT-EQ MENU
MODE
Note:
The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the
MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the
MENU button is
pressed is shown below.
HEAD PHONE
DOLBY HP MODE : ON
SURROUND : OFF
L LEVEL : 0 dB
R LEVEL : 0 dB
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS
→ ON → BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
ON: Dolby headphone mode active.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “
✽✽✽ ” is
displayed as the mode indication.
The surround mode can be selected when mode is
ON.
L/R LEVEL can be set in the ±10 dB range.
Notes:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
• TONE cannot be set when mode is ON.
• The Dolby Headphone function will not work when
32 or 96 kHz PCM digital signals are input.
VIDEO ON/OFF
When no video signal is connected to the SR4001/
SR5001 or a DVD, etc., is connected directly to your
TV, the unnecessary video circuit can be turned off
by selecting the “
VIDEO OFF ” setting.
To select video off, press the AMP button and press
the V-OFF button.
TAPE
REMOTE CONTROLLER RC5001SR
MD CDR CD
DVD
AUX2
VCR
TUNER
DSS TV
AUX1 AMP AMP
- TUNING PRESET - + +
DVD VCR DSS TV
BASS TREBLE
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
SETUP SIMPLE PURE
T-MODE
SURROUND MEMORY DISPLAY
R5001
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
DISPLAY MODE
P.SCAN
T.MODE
1 2 3
4 5 6
7 8 9
SEND
INPUT
EX/ES VIRTUAL CS
dts
P.DIRECT
l/
OFF ON SET
STEREO NIGHT M-CH ST
AUTO
SURROUND SLEEP
LEARN
LIP SYNC/
SOURCE
DISPLAY DISPLAY
SETUP SIMPLE PURE
T-MODE
SURROUND MEMORY DISPLAY
ER SR5001
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
You can select the display mode for the front display
of the SR4001/SR5001.
To select this mode, press the
DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition