Marantz SR4001 - Manual (Page 35)

32
ENGLISH
USING THE SLEEP TIMER
T.MODE
1 2 3
4 5 6
SEND
INPUT
EX/ES VIRTUAL CS
dts
P.DIRECT
l/
OFF ON SET
AUTO
SURROUND DISPLAY
LEARN
LIP SYNC/
SOURCE
SLEEP SLEEP
To program the SR4001/SR5001 for automatic
standby, press the
SLEEP button on the remote.
Each press of the button will increase the time before
shut down in the following sequence.
OFF 10 20 30 40
90 80 70 60 50
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the
SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.
NIGHT MODE
P.SCAN
CAT
T.MODE
1 2 3
4 5 6
7 8 9
0 +10
HT-EQ
SPKR A/B CH/
INPUT
MUTE
EX/ES VIRTUAL CS
VOLUME
dts
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
A/D
LIP SYNC/
MEMO CL
Press the NIGHT button on the remote to turn on the
NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late at
night.
To turn off the Night mode, press the
NIGHT button
again.
SELECTING THE SURROUND MODE
Example: AUTO SURROUND
1 2 3
4 5 6
7 8 9
0 +10
P.SCAN
T.MODE
INPUT
EX/ES VIRTUAL CS
dts
P.DIRECT
l/
OFF ON SET
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
SURROUND SLEEP DISPLAY
A/D
LIP SYNC/
CL
SOURCE
HT-EQ
MEMO
MULTI SPEAKER SETUP SIMPLE MULTI PURE SURROUND
STANDBY
PHONES POWER ON/STANDBY
INPUT SELECTOR AV SURROUND RECEIVER SR5001
DIRECT
AUTO HT-EQ MENU
MODE
To select the surround mode during playback, press
the
SURROUND MODE button on the front panel or
the SURROUND MODE buttons on the remote.
ADJUSTING THE MAIN VOLUME
CAT
CAT
0 +10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
INFO
CH/
M-SPKR
MUTE
7.1CH IN A/D
MEMO CL
VOLUME VOLUME
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO T-MODE
MEMORY SPLAY ATT MUTE
VOLUME
UP DOWN
EXIT BAND
CLEAR
Adjust the volume to a comfortable level using
the
VOLUME control knob on the front panel or
VOLUME 3 / 4 buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME 3 button on the remote,
to decrease the volume, turn counterclockwise or
press
VOLUME 4 button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 27, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
TAPE
- TUNING PRESET - + +
REMOTE CONTROLLER RC5001SR
MD CDR CD
DVD
AMP AUX2
VCR
TUNER
DSS TV
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
AUX1
BASS BASS TREBLE TREBLE
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote control unit)
To adjust the bass effect, press BASS 3 or BASS 4
on the remote.
To adjust the treble effect, press
TREBLE 3 or
TREBLE 4 on the remote.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
TEMPORARILY TURNING OFF
THE SOUND
CAT
CAT
0 +10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
INFO
CH/
M-SPKR
VOLUME
7.1CH IN A/D
MEMO CL
MUTE MUTE
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO T-MODE
MEMORY ISPLAY ATT MUTE
VOLUME
UP DOWN
EXIT BAND
CLEAR
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the
MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“
MUTE ” .
Press the MUTE button again to return to normal
operation.