Document Outline

• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 General
  • 1.2 Pre-Operation
    • Operator Training and Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 Operation
    • General
    • Electrocution Hazards
    • Trip and Fall Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.4 Towing, Lifting, and Hauling
  • 1.5 Maintenance
    • General
    • Maintenance Hazards
    • Battery Hazards
• SECTION 2. USER RESPONSIBILITIES, MACHINE PREPARATION & INSPECTION
  • 2.1 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 Preparation, Inspection, and Maintenance
    • Pre-Start Inspection
    • Function Check
• SECTION 3. USER RESPONSIBILITIES AND MACHINE CONTROLS
  • 3.1 General
  • 3.2 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 3.3 Operating Characteristics and Limitations
    • General
    • Placards
    • Capacities
    • Stability
  • 3.4 Controls and Indicators
    • Ground Control Station
  • 3.5 Platform Control Station
  • 3.6 MDI (Multifunction Digital Indicator)
    • MDI Description
• SECTION 4. MACHINE OPERATION
  • 4.1 Description
  • 4.2 Operation
    • Platform/Ground Select Switch
    • Emergency Stop Switch
  • 4.3 Platform Operation
    • Raising
    • Lowering
    • Arm Guards (If equipped)
    • Platform Extension
    • Fold-Down Rails
  • 4.4 Steering
  • 4.5 Driving
    • Driving Forward
    • Driving in Reverse
  • 4.6 Parking and Stowing
  • 4.7 Battery Charging
    • Operation
    • Battery Charger Fault Codes
  • 4.8 Platform Loading
  • 4.9 Safety Prop
  • 4.10 Tie Down/Lift Lugs
  • 4.11 Lifting
  • 4.12 Towing
    • Remote Electric Brake Release
    • Push Button Electric Brake Release
    • Mechanical Brake Release
    • Mechanical Brake Release
    • Mechanical Brake Release
  • 4.13 Diagnostic Trouble Codes (DTC)
    • Introduction
  • 4.14 Diagnostic trouble codes (DTC) Check Tables
    • 0-0 Help Comments
    • 2-1 Power-Up
    • 2-2 Platform Controls
    • 2-3 Ground Controls
    • 2-5 Function Prevented
    • 3-1 Line Contactor Open Circuit
    • 3-2 Line Contactor Short Circuit
    • 3-3 Ground Output Driver
    • 4-2 Thermal Limit (SOA)
    • 4-4 Battery Supply
    • 6-6 Communication
    • 6-7 Accessory
    • 7-7 Electric Motor
    • 8-1 Tilt Sensor
    • 8-2 Platform Load Sense
    • 9-9 Hardware
• SECTION 5. EMERGENCY PROCEDURES
  • 5.1 General
    • Emergency Stop Switch
    • Manual Descent
  • 5.2 Emergency Operation
    • Operator Unable to Control Machine
    • Platform Caught Overhead
    • Righting of Tipped Machine
    • Post-Incident Inspection
  • 5.3 Incident Notification
• SECTION 6. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 6.1 Introduction
  • 6.1 Operating Specifications
    • Dimensional Data
    • Motors
    • Batteries
    • Capacities
    • Tires
  • 6.1 Critical Stability Weights
    • Lubrication
  • 6.1 Operator Maintenance
    • Oil Check Procedure (1)
    • Lower (2) & Upper Slide Pads (3)
  • 6.1 Tires and Wheels
    • Tire Wear and Damage
    • Wheel and Tire Replacement
    • Wheel Installation
  • 6.1 SUPPLEMENTAL INFORMATION
• SECTION 7. INSPECTION AND REPAIR LOG